manualshive.com logo in svg

Fibocom L860-GL, At Command User Manual, Page: 22 / 254

Share
Download
Fibocom L860-GL At Command User Manual Download Page 22

 

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved. 

FIBOCOM L860 AT Commands User Manual   

 

 

 

 

 

 

 

 

 

 

Page 22 of 254 

Command 

Description 

AT+FMR 
 

[Response/Action] 

+FMR: "<revision>" 
 

OK 
 

Read 

[Function] 

The Read command requests the revision identification. The modem outputs a string 

containing the revision identification information of the software version contained 

within the device. 
 

[Syntax] 

AT+FMR? 
 

[Response/Action] 

+FMR: "<revision>" 
 

OK 
 

Test 

N/A 

Parameters 

N/A 

Example 

AT+FMR 

+FMR: “18600.5001.00.35.00.13” 
 

OK 

 

3.1.10 +CGSN, Request Product Serial Number Identification 

This command displays the product serial number identification IMEI (International Mobile Equipment 

Identification). It can be used even when the SIM card is not inserted. 

Command 

Description 

Execution 

[Function] 

This command displays the product serial number identification IMEI (International 

Mobile Equipment Identification). It can be used even when the SIM card is not 

inserted. 
 

Summary of Contents for L860-GL































































































































































































































































Reviews:

No comments