Fibocom L860-GL Page 122 At Command User Manual Download

Page: 122 / 254

FIBOCOM L860 AT Commands User Manual

Page 122 of 254

Command

Description

AT+CUSATT=?

[Response/Action]

Parameters

<terminal_response>

Is a string type in hexadecimal character format. Terminal response to a proactive

command as defined in 3GPP TS 31.111 [92], consisting of the full BER-TLV data

object.

Example

Reference

3GPP TS 27.007

7.1.6 +CUSATE, Send USAT envelope command

This command is used to send USAT Enevelope command.

Command

Description

Set

[Function]

Set command allows the TE to send a USAT envelope command to the MT. If the UICC

provides response data to the command or indicates that USAT is busy, the information

reCUSATE: <envelope_response>[,<busy>] is returned.

[Syntax]

AT+CUSATE=<envelope_command>

[Response/Action]

+CUSATE: <envelope_response>[,<busy>]

+CME ERROR: <err>

Read

N/A

Test

[Function]

This command only returns OK.

[Syntax]

AT+CUSATE=?

Summary of Contents for L860-GL































































































































































































































































Search results

Summary of Contents for L860-GL

Reviews:

Related manuals for L860-GL

Brands by name

Popular brands

Fibocom L860-GL, At Command User Manual

Search results

Summary of Contents for L860-GL

Reviews:

Related manuals for L860-GL

Brands by name

Popular brands