FIBARO WALLI FGWDSEU-221 Operating Manual Download Page 37

Page: 37 / 39

parts compatIbIlIty

12:

Parts compatibility

Available FIBARO parts

Included in

FGWDSEU-221

Name

Symbol

Wall Double Switch Unit

FG-WDSEU221-AS-8001

Cover Plate with Lightguide

FG-WDSEU221-AS-8003

(FG-Wx-PP-0001

+ FG-WDSEU221-

PP-0005)

Adapter

FG-WDSEU221-PP-0007

Mounting Frame FIBARO/

GIRA

FG-Wx-AS-4001

Mounting Frame Legrand

FG-Wx-AS-4002

Mounting Frame Schneider

FG-Wx-AS-4003

Single Cover Plate

FG-Wx-PP-0001

Double Cover Plate

FG-Wx-PP-0003

Triple Cover Plate

FG-Wx-PP-0004

Wall Double Switch / Dimmer

/ Roller Shutter Lightguide

FG-WDSEU221-PP-0005

Parts not included in the FGWDSEU-221 set are sold separately.

Parts required for GIRA System 55 (only with non-metalised out-

er surface: Standard 55, E2, Event, Event Clear) cover plates

Required FIBARO parts

Name

Symbol

Wall Double Switch Unit

FG-WDSEU221-AS-8001

Adapter

FG-WDSEU221-PP-0007

Mounting Frame FIBARO/

GIRA

FG-Wx-AS-4001

Parts required for Legrand Céliane cover plates

Required FIBARO parts

Name

Symbol

Wall Double Switch Unit

FG-WDSEU221-AS-8001

Adapter

FG-WDSEU221-PP-0007

Mounting Frame Legrand

FG-Wx-AS-4002

Summary of Contents for WALLI FGWDSEU-221








































Search results

Summary of Contents for WALLI FGWDSEU-221

Reviews:

Related manuals for WALLI FGWDSEU-221

Brands by name

Popular brands

FIBARO WALLI FGWDSEU-221, Operating Manual

Search results

Summary of Contents for WALLI FGWDSEU-221

Reviews:

Related manuals for WALLI FGWDSEU-221

Brands by name

Popular brands