FIBARO WALLI FGWDSEU-221 Operating Manual Download Page 32

Page: 32 / 39

confIguratIon

160.

Second button – Switch OFF value sent to 4th and 5th

association groups

Only in Double Switch Mode

Description

This parameter defines value sent with Switch

OFF command to devices associated in 4th and

5th association group.

Parameter size

Default value

Available

values

0 – turn off

1-99 – set level

255 – turn on with previous level

161.

Second button – Double Click value sent to 4th and

5th association groups

Only in Double Switch Mode

Description

This parameter defines value sent with Double

Click command to devices associated in 4th and

5th association group.

Parameter size

Default value

Available

values

0 – turn off

1-99 – set level

255 – turn on with previous level

Summary of Contents for WALLI FGWDSEU-221








































Search results

Summary of Contents for WALLI FGWDSEU-221

Reviews:

Related manuals for WALLI FGWDSEU-221

Brands by name

Popular brands

FIBARO WALLI FGWDSEU-221, Operating Manual

Search results

Summary of Contents for WALLI FGWDSEU-221

Reviews:

Related manuals for WALLI FGWDSEU-221

Brands by name

Popular brands