FIBARO WALLI FGWDSEU-221 Operating Manual Download Page 10 | Manualshive

Page: 10 / 39

background image

10

InstallatIon

When installing with Legrand cover plates:

1. Insert the device with mounting frame* into the mounting box

and secure with mounting claws and screws.

2.  Snap the switch button adapter* to the device.
3.  Snap the new inner cover plate to the device.
4.  Snap the new outer cover plate to the device.
5.  Snap the new switch button to the device.

When installing with Schneider cover plates:

1. Insert the device with mounting frame* into the mounting box

and secure with mounting claws and screws.

2. Snap the new cover plate to the device.
3. Snap the new switch button to the device.

* Switch button adapter and additional mounting frames

are sold separately.

«
...
8
9
10
11
12
...
»

Summary of Contents for WALLI FGWDSEU-221








































Reviews:

No comments

Related manuals for WALLI FGWDSEU-221

Brand: GE Pages: 36

Brand: GE Pages: 8

Brand: Cabletron Systems Pages: 52

ETHERNET Accessories 852 852-0111

Brand: WAGO Pages: 38

SkyEdge II-c Capricorn Pro 4 AC Series

Brand: Gilat Pages: 2

Brand: LOVATO ELECTRIC Pages: 37

Brand: Grizzly Pages: 2

Brand: F&G Pages: 6

Brand: Atlantis Land Pages: 3

Brand: Accton Technology Pages: 547

Brand: VeEX Pages: 22

Brand: TAXON TOOLS Pages: 9

Brand: Cabletron Systems Pages: 14

Brand: UNICOM Pages: 15

Brand: Optex Pages: 2

Brand: Hall Research Technologies Pages: 9

pro-trim PT1000

Brand: Seastar Solutions Pages: 2

Brand: T.I.P. Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands