Parameter No. 15 - Operation of the Dimmer and Roller Shutter
Controller – enabling this option allows the user to dim
lighting/shut roller by associating Dimmer/Roller Shutter
Controller and holding or double press of double switch (only
momentary switch).
'HIDXOWYDOXH
0
$YDLODEOHFRQILJXUDWLRQSDUDPHWHUV
0
- Dimmer/Roller Shutter Controller control is not active
1
- Dimmer/Roller Shutter Controller control is active
Parameter No. 16 - Saving the state of the device after a power
failure. Fibaro Switch returns to the last position saved before
a power failure.
'HIDXOWYDOXH
1
Options for changing the parameter 0-1
0
- Fibaro Switch does not save the state after a power failure, it
returns to "off" position
1
- Fibaro Switch saves its state before power failure
Possibility to change the configuration of the following
parameters [30 – 33, 40 - 43].
0
- DEACTIVATION - the device does not respond to alarm data
frames
1
- ALARM RELAY ON - the device turns on after detecting an alarm
2
- ALARM RELAY OFF - the device turns off after detecting an alarm
3
- ALARM FLASHING - the device periodically changes its status to
the opposite, when it detects an alarm within 10 min.
Parameter No. 30 - General Alarm, set for relay no. 1.
'HIDXOWYDOXH
3[byte] ALARM FLASHING
Parameter No. 40 - General Alarm, set for switch no. 2.
'HIDXOWYDOXH
3[byte] ALARM FLASHING
Parameter No. 31 - Alarm of flooding with water, set for relay
no. 1.
'HIDXOWYDOXH
2[byte] ALARM RELAY OFF
Parameter No. 41 - Alarm of flooding with water, set for relay
no. 2.
'HIDXOWYDOXH
2[byte] ALARM RELAY OFF
Parameter No. 32 - Smoke, CO, CO2 Alarm. Set for relay no. 1.
'HIDXOWYDOXH
3[byte] ALARM FLASHING
Parameter No. 42 - Smoke, CO, CO2 Alarm. Set for relay no. 2.
'HIDXOWYDOXH
3[byte] ALARM FLASHING
Parameter No. 33 - Temperature Alarm, set for relay no. 1.
'HIDXOWYDOXH
1[byte] ALARM RELAY ON
Parameter No. 43 - Temperature Alarm, set for relay no. 2.
'HIDXOWYDOXH
1[byte] ALARM RELAY ON
Parameter No. 39 - Active flashing alarm time.
'HIDXOWYDOXH
600
$YDLODEOHFRQILJXUDWLRQSDUDPHWHUV>@>PV@
VI Additional Functionality
Operating alarm data frames
Fibaro system allows user to set response of devices to alarm
situations (response to data-frames ALARM_REPORT and
SENSOR_ALARM_REPORT) Fibaro Double Relay Switch responds
WRWKHIROORZLQJW\SHVRIDODUPV
*HQHUDO3XUSRVH$ODUP*(1(5$/385326($/$50>[@
6PRNH$ODUP $/$50 &2 >[@$/$50 &2 >[@$/$50
SMOKE [0x03]
:DWHU)ORRGLQJ$ODUP$/$50:$7(5>[@
7HPSHUDWXUH$ODUP$/$50+($7>[@
Alarm data-frames are sent by devices that are system sensors (e.g.,
flood sensors, smoke detectors, motion detectors, etc.).
The device may respond in the following manner to received
data-frames (settings are configured in configuration parameters,
VHHVHFWLRQ9&RQILJXUDWLRQ
'($&7,9$7,21WKHGHYLFHGRHVQRWUHVSRQGWRDODUPGDWD
frames
$/$5021WKHGHYLFHWXUQVRQDIWHUGHWHFWLQJDQDODUP
$/$502))WKHGHYLFHWXUQVRIIDIWHUGHWHFWLQJDQDODUP
$/$50)/$6+,1*WKHGHYLFHSHULRGLFDOO\FKDQJHVLWVVWDWXV
to the opposite when it detects an alarm (lights on/off alternately)
Fibaro Double Relay Switch has two independent alarm group (i.e.
each of its channels may respond in an individual way to received
alarm data-frames).
,;*8$5$17((
1. The Guarantee is provided by FIBAR GROUP Sp. z o.o.
(hereinafter "Manufacturer"), based in Poznan, ul. Lotnicza 1; 60-421
Poznan, entered in the register of the National Court Register kept
E\ WKH 'LVWULFW &RXUW LQ 3R]QDĔ 9,,, (FRQRPLF 'HSDUWPHQW RI WKH
1DWLRQDO &RXUW 5HJLVWHU QR 1,3 5(*21
301595664.
2. The Manufacturer is responsible for equipment malfunction
resulting from physical defects (manufacturing or material) of the
Device for 12 months from the date of its purchasing.
3. During the Guarantee period, the Manufacturer shall remove any
defects, free of charge, by repairing or replacing (at the sole
discretion of the Manufacturer) any defective components of the
Device with new or regenerated components, that are free of
defects. When the repair impossible, the Manufacturer reserves the
right to replace the device with a new or regenerated one, which shall
be free of any defects and its condition shall not be worse than the
original device owned by the Customer.
4. In special cases, when the device cannot be replaced with the
device of the same type (e.g. the device is no longer available in the
commercial offer), the Manufacturer may replace it with a different
device having technical parameters similar to the faulty one. Such
activity shall be considered as fulfilling the obligations of the
Manufacturer. The Manufacturer shall not refund money paid for the
device.
5. The holder of a valid guarantee shall submit a guarantee claim
WKURXJK WKH JXDUDQWHH VHUYLFH 5HPHPEHU EHIRUH \RX VXEPLW D
guarantee claim, contact our technical support using telephone or
e-mail. More than 50% of operational problems is resolved remotely,
saving time and money spent to initiating guarantee procedure. If
remote support is insufficient, the Customer shall fill the guarantee
claim form (using our website - www.fibargroup.com) in order to
obtain claim authorization.
When the guarantee claim form is submitted correctly, the Customer
shall receive the claim confirmation with an unique number (Return
Merchandise Authorization -RMA).
6. The claim may be also submitted by telephone. In this case, the
call is recorded and the Customer shall be informed about it by a
consultant before submitting the claim. Immediately after submitting
the claim, the consultant shall provide the Customer with the claim
number (RMA-number).
7. When the guarantee claim form is submitted correctly, a
representative of the Authorised Guarantee Service (hereinafter as
"AGS") shall contact the Customer.
8. Defects revealed within the guarantee period shall be removed
not later than 30 days from the date of delivering the Device to AGS.
The guarantee period shall be extended by the time in which the
Device was kept by AGS.
9. The faulty device shall be provided by the Customer with complete
standard equipment and documents proving its purchase.
10. Parts replaced under the guarantee are the property of the
Manufacturer. The guarantee for all parts replaced in the guarantee
process shall be equal to the guarantee period of the original device.
The guarantee period of the replaced part shall not be extended.
11. Costs of delivering the faulty device shall be borne by the
Customer. For unjustified service calls, the Service may charge the
Customer with travel expenses and handling costs related to the
case.
$*6VKDOOQRWDFFHSWDFRPSODLQWFODLPRQO\ZKHQ
WKH'HYLFHZDVPLVXVHGRUWKHPDQXDOZDVQRWREVHUYHG
WKH 'HYLFH ZDV SURYLGHG E\ WKH &XVWRPHU LQFRPSOHWH ZLWKRXW
accessories or nameplate,
LWZDVGHWHUPLQHGWKDWWKHIDXOWZDVFDXVHGE\RWKHUUHDVRQVWKDQ
a material or manufacturing defect of the Device
WKH JXDUDQWHH GRFXPHQW LV QRW YDOLG RU WKHUH LV QR SURRI RI
purchase,
13. The Manufacturer shall not be liable for damages to property
caused by defective device. The Manufacturer shall not be liable for
indirect, incidental, special, consequential or punitive damages, or
for any damages, including, inter alia, loss of profits, savings, data,
loss of benefits, claims by third parties and any property damage or
personal injuries arising from or related to the use of the Device.
7KHJXDUDQWHHVKDOOQRWFRYHU
PHFKDQLFDOGDPDJHVFUDFNVIUDFWXUHVFXWVDEUDVLRQVSK\VLFDO
deformations caused by impact, falling or dropping the device or
other object, improper use or not observing the operating manual);
GDPDJHV UHVXOWLQJ IURP H[WHUQDO FDXVHV HJ IORRG VWRUP ILUH
lightning, natural disasters, earthquakes, war, civil disturbance, force
majeure, unforeseen accidents, theft, water damage, liquid leakage,
battery spill, weather conditions, sunlight, sand, moisture, high or low
temperature, air pollution;
GDPDJHVFDXVHGE\PDOIXQFWLRQLQJVRIWZDUHDWWDFNRIDFRPSXWHU
virus, or by failure to update the software as recommended by the
Manufacturer;
GDPDJHVUHVXOWLQJIURPVXUJHVLQWKHSRZHUDQGRUWHOHFRPPXQL
-
cation network, improper connection to the grid in a manner
inconsistent with the operating manual, or from connecting other
devices not recommended by the Manufacturer.
GDPDJHVFDXVHGE\RSHUDWLQJRUVWRULQJWKHGHYLFHLQH[WUHPHO\
adverse conditions, i.e. high humidity, dust, too low (freezing) or too
high ambient temperature. Detailed permissible conditions for
operating the Device are defined in the operating manual;
GDPDJHVFDXVHGE\XVLQJDFFHVVRULHVQRWUHFRPPHQGHGE\WKH
Manufacturer
GDPDJHVFDXVHGE\IDXOW\HOHFWULFDOLQVWDOODWLRQRIWKH&XVWRPHU
including the use of incorrect fuses;
GDPDJHVFDXVHGE\&XVWRPHUVIDLOXUHWRSURYLGHPDLQWHQDQFHDQG
servicing activities defined in the operating manual;
GDPDJHV UHVXOWLQJ IURP WKH XVH RI VSXULRXV VSDUH SDUWV RU
accessories improper for given model, repairing and introducing
alterations by unauthorized persons;
GHIHFWVFDXVHGE\RSHUDWLQJIDXOW\'HYLFHRUDFFHVVRULHV
15. The scope of the guarantee repairs shall not include periodic
maintenance and inspections, in particular cleaning, adjustments,
operational checks, correction of errors or parameter programming
and other activities that should be performed by the user (Buyer).
The guarantee shall not cover natural wear and tear of the Device
and its components listed in the operating manual and in technical
documentation as such elements have a defined operational life.
16. If a defect is not covered by the guarantee, the Manufacturer
reserves the right to remove such defect at its sole discretion,
repairing the damaged or destroyed parts or providing components
necessary for repair or replacement.
17. This guarantee shall not exclude, limit or suspend the Customer
rights when the provided product is inconsistent with the purchase
agreement.
This Device may be used with all devices
certified with Z-Wave certificate and should be
compatible with such devices produced by
other manufacturers.
Any device compatible with Z-Wave may be added
to Fibaro system.
i
FIBARGROUP
FIBARO
In case of any technical questions contact customer service centre
in your country.
www.fibargroup.com
VII Operating Fibaro Switch
)LEDUR6ZLWFKPD\EHRSHUDWHGXVLQJWKHIROORZLQJFRQWUROHOHPHQWV
í DQ\ FRQWUROOHU FRPSDWLEOH ZLWK WKH V\VWHP HJ +RPH &HQWHU
controller)
íDPRELOHSKRQHHJL3KRQHDQGSKRQHVIURPRWKHUPDQXIDFWXUHUV
with appropriate software)
íWDEOHWVXFKDVL3DG
í3&XVLQJDZHEEURZVHU
íSXVKEXWWRQVFRQQHFWHGWRLQSXWV6DQG6
í VHUYLFH EXWWRQ % ORFDWHG LQVLGH WKH KRXVLQJ DFWLYDWHV OHDUQ
monde)
The device does not respond to a pre-programmed transmitter:
0DNHVXUHWKDWWKHPD[LPXPUDQJHLVQRWH[FHHGHGDQGWKHVLJQDO
path is not obstructed by metal surfaces such as metal cabinets, etc.
0DNHVXUHWKHGHYLFHLVQRWLQWKHSURJUDPPLQJPRGHRUUHSHDW
the programming process.
2UUHSHDWWKHSURJUDPPLQJSURFHVV
VIII Procedures for malfunctions
