Fiat Punto 2004 Training Manual Download Page 148

Page: 148 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

3.10.4 Idling speed check

The control unit processes the signals from the various sensors (engine revs; engine

temperature; vehicle speed) and adjusts the amount of injected fuel:

it controls the pressure regulator (DRV2);

it varies the injection time of electric injectors (CR1MI2.2).

Within some thresholds, the speed allows for the battery voltage.

gb Fiat Grande Punto OK

148 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands