Fetco E1251IN-1B140-PM110, Users Manual And Operator Instructions

Page: 6 / 32

Go to fetco.com for the latest versions of all information
Page 6 User Guide & Operator instructions P213 e0 NOVEMBER 2021
Starting The Brew
1. Turn the power switch “ON”. (Twin Shown)
2. Prepare a brew basket with the correct size filter and appropriate amount of
coffee.
3. Slide the brew basket completely into the rails.
4. Place a clean, empty, and preheated dispenser under the brew basket.
5. Select a batch & hold the corresponding BREW button in for 1 second to start
6. -STOP button will illuminate,
-Countdown time will display,
-Selected BREW button will flash to indicate brew is in progress.
-All other BREW buttons for that brew head will extinguish.
7. When the brew cycle is finished,
STOP button will extinguish and the BREW button will continue to flash for the
amount of time programmed into the DRIP DELAY setting.
This indicates that coffee may still be dripping from the brew basket
For safety- do not remove brew basket until drip-out is complete.
Twin Brewer ready to brew. Example shown: Pressing top right brew position Brewing-see #6 above
RECIPE Location map
Viewing and changing settings for the brew
recipes is from the “A” screens with the controls in
PROGRAMMING.
The uppermost button positions are permanent
and will not display programming step A_0. The
table above shows in position A20 that a button
position can be made
active or inactive
.
Position A1 does not display this step

DISPLAY
 
DISPLAY

STOP
 
STOP

BATCH
A1

(permanent)

BATCH
A4
(permanent)

BATCH A2

(enabled by factory)

BATCH A5
(enabled by factory)

BATCH
A3

(disabled by factory)

BATCH
A6
(disabled by factory)
The “A” menu is the most accessed menu. It is for programming the batch volumes, brewing parameters, enabling or
disabling brew buttons. The “A” menu moves through the six positions(CBS-1252-) or three positions(CBS-1251+) by
entering the menu and pressing the left stop button. (only the left side is active for programming the CBS-1252+)
The A menus [A1-3 or A1-6] correspond to batch buttons [3 or 6] on the touch panel
Access the A menus to PROGRAM & make changes to individual menu recipes. Menu settings can be copied
Menu positions A1 and A4 [top position] are permanent. Menus A2, A3, A5, A6 can be removed by operator if desired
From A PRG screen
Press button 1 to go
into to the A menu
access screens.
Continue pressing
button #1 to enter
progamming for A1
From A11 screen
Press STOP to
scroll to A20.
(A1&A4 are permanent)
From A20 screen
Press STOP to
scroll through the
remaining (3 or 6)
“A” menus. Make
any changes as
required
From A60 screen
Scroll out to
remaining A10-to
A70 programming
keys. See SAVE &
EXIT in previous
table
For single and twin
Position of batch
buttons for CBS-1252+
The CBS-1251+ single
position brewer has
one row of buttons
STOP
Ready Brewing
5:30
STOP
STOP
Single Side Models
CBS-1231 Plus
STOP STOP
Dual Side Models
CBS-1232 Plus
Batch Program
A1
STOP
STOP
STOP
Brew Volume
A1.10 3.80L +/-
STOP
STOP
Batch Enabled
A6.00 NO+
STOP
(Dual model shown)
Batches A1 to A6
STOP STOP
A1
A2
A3
A4
A5
A6
STOP
FETCO
Ready to Brew
STOP
Batch Enabled
A2.00 YES -
STOP
STOP