background image

Festo — CPX-AP-A-PN-M12 — 2022-07

Diagnostics and fault clearance

23

9.4

Diagnostics via Web Server

A webserver is available to display the diagnostics messages.
The web server can be accessed by entering the IP address in the address bar of a web browser.

9.5

Diagnostics via PROFINET IO

The automation system CPX-AP-A supports diagnostic options via PROFINET IO in accordance with
IEC 61158, e.g. module-related and channel-related status information as well as error detection in the
online mode of the control software and in the user program of the high-order controller.
Diagnostic messages from the automation system CPX-AP-A that cannot be seen on the PROFINET
standard diagnostics are shown as manufacturer-specific PROFINET channel diagnostics.
For PROFINET, only the lower 16 bits of the diagnostics ID (error number) are shown.
The display rule is as follows:

Error number 1 … 32767:
ChannelErrType = 2001 with ExtChannelErrType = error number

Error number 32768 … 65535:
ChannelErrType = 2002 with ExtChannelErrType = error number – 32768

The error number 0 is reserved.

Information on grouping and displaying the diagnostic messages

è

 Instructions for the automation system CPX-AP-A.

Summary of Contents for PROFINET CPX-AP-A-PN-M12





























Reviews: