manualshive.com logo in svg

Festo EXCH-40-...-AB1 Series, Mechanical Installation

Share
Download
Festo EXCH-40-...-AB1 Series Mechanical Installation Download Page 44

5

Mounting (horizontal mounting position)

44

Festo – GDCP-EXCH-KM-KOMP-EN – 1506a – English

5

Mounting (horizontal mounting position)

5.1

Mounting

5.1.1

Safety instructions

Warning

Inappropriate mounting material will cause the planar surface gantry mounting to come

loose during mounting or operation.

Danger of serious injuries.

 Use mounting components and mounting surface with sufficient strength.

 Observe weight of the planar surface gantry.

Warning

Danger of crushing when handling due to the weight or tilting of the planar surface

gantry.

The planar surface gantry has an asymmetrical centre of gravity.

For stabilisation and to avoid distortions, two transport protection aids are attached to

the X-axes.

 Use only the transport lugs for transport.

 Fasten the lifting gear to the 4 transport lugs.

 No person may stand under the planar surface gantry during transport with lifting

gear.

 Observe the weight of the planar surface gantry, which depends on the size and

accessories.

 Observe different weight distribution.

 Remove transport protection aids on the X-axes only after mounting the planar sur­

face gantry to the mounting surface.

Warning

Danger of crushing due to uncontrolled movements of the traverse (Y-axis).

 Make sure that the traverse is located at the end caps in the end position (opposite

the motor side) and is secured against uncontrolled movements with the transport

attachments.

Note

For mounting, Festo recommends the adjusting kits as mounting accessories.

 After alignment, the limits of the axis alignment must be complied with (

è

 5.2.2).

Summary of Contents for EXCH-40-...-AB1 Series









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands