EMCS-YY-ST
Integrated drive
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Brief instruction
8174315
2022-04a
[8174317]
Translation of the original instructions
© 2022 all rights reserved to Festo SE & Co. KG
1
About this document
1.1
Applicable documents
All available documents for the product
Type
Product
Contents
Integrated drive
EMCS-ST
Integrated drive
Manual
Drive system
EGSS-BS
Mini slide unit
Operating instructions
ELGE-TB
Toothed belt axis unit
Operating instructions
ELGS-BS
Spindle axis unit
Operating instructions
ELGS-TB
Toothed belt axis unit
Operating instructions
EPCS-BS
Electric cylinder unit
Operating instructions
Drive
EGSC
Mini slide
Operating instructions
ELGR-TB
Toothed belt axis
Operating instructions
ELGC-BS
Spindle axis
Operating instructions
ELGC-TB
Toothed belt axis
Operating instructions
EPCC-BS
Electric cylinder
Operating instructions
Mounting kit
EAMM
Axial and parallel kit
Assembly instructions
IO-Link cable
NEFC
Adapter
Assembly instructions
Tab. 1: Applicable documents for the product
1.2
Product version
This documentation refers to the following datasets:
–
Firmware version of the integrated drive from "v19.0.4.107_release"
–
IO-Link device description file (IODD) from V1.2.6
–
Adapter NEFC from production date 01/2022
If a different firmware version is used, check whether there is a correspondingly
newer version of the documentation
1.3
Product labelling
1
Fig. 1: Product labelling
1
Product labelling (product information,
approvals, warning symbol)
Warning symbol
Warning
symbol
Meaning
Attention! Hot surface
Metallic housing parts of the device can reach high temperatures during operation. In
the event of a fault, internal components may become overloaded.
Tab. 2: Warning symbol
1.4
Specified standards
Version
IEC 60204-1:2005+AMD1:2008 CSV
EN 61800-5-1:2016-08
IEC 61131-2:2013
EN 60034-1:2011-02
EN 61800-2:2016
EN 60204-1:2006+A1:2009+AC:2010
Tab. 3: Standards specified in the document
2
Safety
2.1
Safety instructions
–
Only use the product if it is in perfect technical condition.
–
Only use the product in its original condition without unauthorised modifica-
tions.
–
Do not carry out repairs on the product. Replace defective product immediately.
–
Observe the identifications on the product.
–
Never remove or insert the plug connector while live.
–
Operate the product only in an installed condition when all required protective
measures have been taken
è
EN 60204-1.
–
Before working on the product, switch off the power supply and secure it
against being switched on again.
–
Store the product in a cool, dry environment protected from UV and corrosion.
Keep storage times short.
2.2
Intended use
The intended use of the EMCS-ST integrated drive is to power the connected
actuator technology. The integrated electronics enable control of position, speed
or force/torque.
2.2.1
Application areas
The device is intended for use in an industrial environment. Outside industrial
environments, e.g. in commercial and residential/mixed-use areas, it may be
necessary to take measures to suppress radio interference.
2.3
Training of qualified personnel
Work on the product may only be carried out by qualified personnel who can
evaluate the work and detect dangers.
The qualified personnel have knowledge and experience in dealing with electric
drive systems.
2.4
Approvals and certifications
CE approval (conformity)
In conjunction with the CE mark on the product, the EC directives and standards
listed below in the Declaration of Conformity
–
in accordance with EU EMC Directive
–
in accordance with EU RoHS Directive
KC certification
KC number: R-R-FTO-KC-2018-1082
RCM certification
The product fulfils the EMC requirements for Australia and New Zealand with the
RCM certification mark on the product.
3
Additional information
–
Contact the regional Festo contact if you have technical problems
–
Accessories and spare parts
4
Product overview
4.1
Scope of delivery
The following components are included in the scope of delivery:
–
Integrated drive EMCS-YY-ST-... (Spare part)
–
Instruction manual for the integrated drive EMCS-YY-ST