Festo EMCA-EC-67 CO Series Description Download

Page: 299 / 416

FHPP parameters (PNU)

Festo – EMCA-EC-C-HP-EN – 2017-11e – English

299

PNU 566

Stroke limiter (Stroke limit)

Subindex 1

Class: Var

Data type: int32

Mappable

Access: rw2

Reading or parameterisation of the max. permitted displacement (stroke) [SINC] with active speed

adjustment.

With active speed adjustment, the actual position relative to the start position must not change by

more than the amount specified in this parameter. In this way, you can ensure that the axis will not

perform an uncontrolled movement if speed adjustment is activated by mistake.

Monitoring can be activated or deactivated via the control bit “Stroke limit value deactivated

(CDIR.XLIM, B5)”.

Tab. C.114 PNU 566

PNU 568

Speed deviation message window

(Velocity control deviation window)

Subindex 1

Class: Var

Data type: int32

Mappable

Access: rw1

Reading or parameterisation of the permitted displacement [SINC/s] with active speed adjustment.

Tab. C.115 PNU 568

Summary of Contents for EMCA-EC-67 CO Series

































































































































































































































































































































































































































Search results

Summary of Contents for EMCA-EC-67 CO Series

Reviews:

Related manuals for EMCA-EC-67 CO Series

Brands by name

Popular brands

Festo EMCA-EC-67 CO Series, Description

Search results

Summary of Contents for EMCA-EC-67 CO Series

Reviews:

Related manuals for EMCA-EC-67 CO Series

Brands by name

Popular brands