Festo CPX-E-CEC PN, Instructions, Page: 5 / 5

Connection status [XF1], [XF2]
LED
(green) Meaning Remedy
Flashes
Module locating in progress when both
LEDs are flashing in synchronisation,
e.g. for troubleshooting or configuration. –
Off
No connection at the respective port or
line not connected. Check network connection.
Tab. 15 Connection Status [XF1], [XF2]
12 Disposal
ENVIRONMENT!
Send the packaging and product for environmentally sound recycling in accord-
ance with the current regulations
è www.festo.com/sp.
13 Technical Data
13.1 General Technical Data
General technical data
General technical data
Automation system CPX-E Description of automation system CPX-E
è
1.1 Applicable Documents
Dimensions
(length x× width × height)
1)
[mm] 124.3 × 75.9 × 82.5
Product weight
2)
[g] 288
Mounting position Vertical/horizontal
Ambient temperature with
vertical mounting position [°C] –5 … +60
3)
Ambient temperature with
horizontal mounting position [°C] –5 … +50
3)
Storage temperature [°C] –20 … +70
Humidity
(non-condensing) [%] 0 … 95
Degree of protection in accordance with
EN 60529 IP20
The degree of protection is not UL-tested.
Protection against electric shock
(Protection against direct and indirect
contact in accordance with IEC 60204-1) through the use of PELV circuits
(protected extra-low voltage)
Electromagnetic compatibility To EN 61000-6-2/-4 and NE 21
Module code/sub-module code
CPX-E-CEC-C1-PN 222/100
CPX-E-CEC-M1-PN 222/101
Module identification
CPX-E-CEC-C1-PN E-CEC-C1-PN
CPX-E-CEC-M1-PN E-CEC-M1-PN
1) Including covering, not including linking element
2) Including linking element
3) for non-conforming technical data see UL operating conditions table UL
Tab. 16 General Technical Data
Power supply
Operating power supply
U
EL/SEN
[V DC] 24 _ 25%
Intrinsic current consumption
at nominal operating voltage
24 V from U
EL/SEN
[mA] 130
Reverse polarity protection
24 V U
EL/SEN
against 0 V
U
EL/SEN
Yes
Mains buffering time [ms] 20
Tab. 17 Power Supply
Network-specific data
Protocol PROFINET
1)
, EtherCAT
Specification Standards and norms with reference to PROFINET:
IEC 61158
IEC 61784
IEC 61918
Transmission rate [Mbps] 100
Crossover detection Auto-MDI/MDI-X
Maximum cable length per
segment [m] 100
Cable specification
Cable type Ethernet twisted pair cable, shielded
Transmission class Category Cat 5 or higher
Cable diameter [mm] 6 … 8
Wire cross section [mm
2
] 0.14 … …0.75; 22 AWG
2)
1) based on the Ethernet protocol IEEE 802.3
2) required for maximum connection length between network participants
Tab. 18 Network-specific Data
13.2 Technical Data UL/CSA Certification
Ambient conditions UL/CSA
Pollution degree 3
Installation site for indoor use only
Max. installation height [m] 2000
Tab. 19 Ambient Conditions UL/CSA
Ambient temperature
Mounting position Vertical Horizontal
Operating power supply U
EL/SEN
via XD
Ambient temperature, max. current rating
of terminal strip
£
4 A
[°C] –5 … +60 –5 … +50
Ambient temperature, max. current rating
of terminal strip
>
4 … 8 A
[°C] –5 … +50 –5 … +40
Operating voltage U
EL/SEN
with feed via both connections [XD]
1)
Ambient temperature, max. current rating
of terminal strip
>
4 … 8 A
[°C] –5 … +60 –5 … +50
1) see chapter 'Product design' or 'Connection elements'
Tab. 20 Ambient temperature ranges