manualshive.com logo in svg

Festo CMMP-AS-***-M0 Series, Manual

Share
Download
Festo CMMP-AS-***-M0 Series Manual Download Page 175

7

Operating modes

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

175

Value

Significance

-1

Invalid operating mode or change in operating mode

-11

User Position Mode

-13

User Velocity Mode

-14

User Torque Mode

1

Profile Position Mode (position controller with positioning mode)

3

Profile Velocity Mode (speed regulator with setpoint value ramp)

4

Profile Torque Mode (torque controller with setpoint value ramp)

6

Homing Mode (reference travel)

7

Interpolated Position Mode

8

Cyclic Synchronous Position Mode (only for EtherCAT)

The operating mode can only be set via the object modes_of_operation. Since a change in

operating mode can take some time, one must wait until the newly selected mode

appears in the object modes_of_operation_display. During this time, “Invalid operating

mode” (-1) may be displayed briefly.

7.2

Operating mode reference travel (homing mode)

7.2.1

Overview

This chapter describes how the motor controller searches for the initial position (also called point of

reference, reference point or zero point). There are various methods to determine this position,

whereby either the limit switch can be used at the end of the positioning range or a reference switch

(zero-point switch) within the possible travel distance. To achieve a reproducibility that is as large as

possible, the zero pulse of the angle encoder used (resolver, incremental encoder, etc.) can be included

with some methods.

Homing

controlword

homing_speeds

homing_acceleration

homing_offset

statusword

position_demand_value

Fig. 7.1

Reference travel

The user can determine the speed, acceleration and type of reference travel . With the object 

home_offset, the zero position of the drive can be displaced to any position desired.

Summary of Contents for CMMP-AS-***-M0 Series







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands