Festo 548076 Page 64 Repair Instructions Download

Page: 64 / 92

64 / 92

Festo 7DHTGd_en

9. Lever the O-ring out of the inside of the hole in the plate.

10. Lever the two rails of the guide segments out of the housing.

If only plate components have to be repaired, you can continue with the assembly in

Chapter 4.5.6 on page 82

4.4.5

Removing the gear racks

The installation position of several components depends on the configuration of the rotary indexing table and can

differ from the images shown here.
The position of the gear racks, indexing pins, blanking plugs and shock absorber must always be marked for
subsequent assembly.

1. Loosen the socket head screws in the impact plate on the front of the hous-

ing (do not unscrew and remove).

2. Unscrew hollow screw in the impact plate.

Note

The impact plate is subjected to spring tensioning on one side and can tilt
when the socket head screws are unscrewed.

3. Unscrew the socket head screws in the impact plate.

Type

Number of socket head screws

DHTG-65-…-A

DHTG-90-…-A

DHTG-140-…-A

DHTG-220-…-A

Summary of Contents for 548076





























































































Search results

Summary of Contents for 548076

Reviews:

Related manuals for 548076

Brands by name

Popular brands

Festo 548076, Repair Instructions

Search results

Summary of Contents for 548076

Reviews:

Related manuals for 548076

Brands by name

Popular brands