Ferris SNAPPER PRO EZ Dump Operator'S Manual Download Page 3

Not for 

Reproduction

3

General Information

Thank you for purchasing this quality-built grass collection

system. When operated and maintained according to the

instructions in this manual, your grass collection system will

provide you many years of dependable service.
This manual contains safety information to make you aware

of the hazards and risks associated with this product and

how to avoid them. This product is designed and intended to

be used and maintained according to the manual for grass

collection from established lawns and is not intended for any

other purpose. It is important that you read and understand

these instructions thoroughly before attempting to operate

this equipment. 

Save these original instructions for future

reference.

These setup instructions are to be done in addition to the

Blower and Blower Mount installation instructions detailed

in the blower's operators manual included with the blower

mount.
You must observe and obey all safety instructions in the

blower's operator's manual along with all instructions detailed

in this manual.

The images in this document are representative, and

are meant to complement the instructional copy they

accompany. Your unit may vary from the images

displayed. 

LEFT

 and 

RIGHT

 are as seen from the operator's

position. 

Date of

Purchase:

FERRIS is a trademark of Briggs & Stratton, Milwaukee, WI,

USA.
SNAPPER PRO is a trademark of Briggs & Stratton,

Milwaukee, WI, USA.

Products Covered by this

Manual

TURBO-Pro Blower w/ 12 cu. ft. EZ Dump Hopper 

 

System

Number

 

 

Description

 

5600901 

Kit, 12 cu. ft. EZ Dump Hopper w/ TURBO-Pro MAX

Blower, 61", 200XT, IS2100Z, F210Z 

5600902 

Kit, 12 cu. ft. EZ Dump Hopper w/ TURBO-Pro MAX

Blower, 52", IS2100Z 

5600904 

Kit, 12 cu. ft. EZ Dump Hopper w/ TURBO-Pro MAX

Blower, 52", 150XT, F160Z 

5601243

Kit, 12 cu. ft. EZ Dump Hopper w/ TURBO-Pro MAX

Blower, 52", ISX2200

5601245

Kit, 12 cu. ft. EZ Dump Hopper w/ TURBO-Pro MAX

Blower, 61", ISX2200

FAST-Vac® Blower w/ 12 cu. ft. EZ Dump Hopper 

 

System

Number

 

 

Description

 

FAST-Vac® Blower w/ 12 cu. ft. EZ Dump Hopper 

5600903 

Kit, 12 cu. ft. EZ Dump Hopper w/ FAST-Vac® Blower,

61", 200XT, IS2100Z, F210Z 

5600905 

Kit, 12 cu. ft. EZ Dump Hopper w/ FAST-Vac® Blower,

52", 150XT, F160Z 

5600906 

Kit, 12 cu. ft. EZ Dump Hopper w/ FAST-Vac® Blower,

52", IS2100Z 

5601242

Kit, 12 cu. ft. EZ Dump Hopper w/ FAST-Vac® Blower,

52" ISX2200

5601244

Kit, 12 cu. ft. EZ Dump Hopper w/ FAST-Vac® Blower,

61" ISX3300

TURBO-Pro Blower w/ 14 cu. ft. EZ Dump XL Hopper 

 

System

Number

 

 

Description

 

5600910 

Kit, 14 cu. ft. EZ Dump XL Hopper w/ TURBO-Pro MAX

Blower, 61", IS3200Z, F320Z 

5600900 

Kit, 14 cu. ft. EZ Dump XL Hopper w/ TURBO-Pro MAX

Blower, 61", S200XT 

5900940 

Kit, 14 cu. ft. EZ Dump XL Hopper w/ TURBO-Pro MAX

Blower, 61", F210Z 

5601241

Kit, 14 cu. ft. EZ Dump XL Hopper w/ TURBO-Pro MAX

Blower, 61" ISX3300

FAST-Vac® Blower w/ 14 cu. ft. EZ Dump XL Hopper 

 

System

Number

 

 

Description

 

5600907 

Kit, 14 cu. ft. EZ Dump XL Hopper w/ FAST-Vac®

Blower, 61", IS3200Z, F320Z 

5600909 

Kit, 14 cu. ft. EZ Dump XL Hopper w/ FAST-Vac®

Blower, 61", S200XT 

5600941 

Kit, 14 cu. ft. EZ Dump XL Hopper w/ FAST-Vac®

Blower, 61", F210Z 

5601240

Kit, 14 cu. ft. EZ Dump XL Hopper w FAST-Vac® Blower,

61" ISX3300

Operator Safety

In addition to all of the safety instructions described in this

manual, you must obey all the safety instructions in the

blower's operators manual included with the blower mount.

Safety Rules and Information

Read these safety instructions and follow them closely.

Failure to obey these rules could result in loss of control of

unit, severe personal injury or death to you, or bystanders, or

damage to property or equipment.

This mowing deck is capable of amputating hands and

feet and throwing objects.

The triangle (

) in text signifies important cautions or

warning which must be followed.

Summary of Contents for SNAPPER PRO EZ Dump





























Reviews: