background image

Not for 

Reproduction

14

ferrismowers.com

Callout

Control Name

B

Malfunction Indicator Lamp (M.I.L.)

C

Throttle Control

D

PTO (Power Take Off) Switch

E

Ignition Switch

F

Fuel Level Gauge

G

Throttle Rocker Switch

Hour Meter:

 This unit is equipped with a dual function hour

meter that records the number of hours that the engine has

run and the number of hours that the PTO switch has been

engaged.

"A" - Hour Glass Icon

 - The hour glass icon flashes when

the hour meter is recording the passage of time.

"B" - Mode Icon

 - The mode icon will display an "E" when

displaying engine hours, and a "P" when displaying PTO

hours.

"C" - Time Display

 - This is the number of hours that are

recorded.
The default display of the hour meter is engine hours. The

mode icon will display a "E" and the hour glass icon will not

flash.
To begin recording engine hours, start the unit's engine and

release the parking brake. The hour glass icon will flash.
To begin recording PTO hours, pull the PTO switch up to

engage the PTO clutch. The unit's engine must be running.

The mode icon will display a "P" and the hour glass icon will

flash.
While recording PTO hours, the hour meter also records

engine hours; however, the hour meter only displays PTO

hours when recording PTO hours.
To stop recording PTO hours, push the PTO switch down to

disengage the PTO clutch.
To stop recording engine hours, engage the parking brake.
The hour meter has a self contained power source so that the

recorded hours are always visible even when the engine is

OFF.

Malfunction Indicator Lamp (M.I.L.):

 The malfunction

indicator lamp detects problems with the engine. If the

malfunction indicator lamp begins to flash while you are

operating the unit, see the engine operator's manual.

Throttle Control:

 The throttle controls engine speed. Move

the throttle forward to increase engine speed and back to

decrease engine speed. Always operate at FULL throttle

when mowing.

Fast throttle speed.

Slow throttle speed.

 

PTO (Power Take Off) Switch:

 The PTO switch

engages and disengages the mower blades. Pull UP on the

switch to engage, and push DOWN to disengage.

Ignition Switch:

 The ignition switch starts and stops the

engine, it has three positions:

OFF

Stops the engine and shuts off the electrical

system.

RUN

Allows the engine to run and powers the

electrical system.

START Cranks the engine for starting.

NOTE: Never leave the ignition switch in the RUN position

with the engine stopped—this drains the battery.

 

 Fuel Level Gauge:

 Displays the fuel level in the tank.

The fuel level gauge is installed in the top of the fuel tank and

is viewed by looking through the port hole in the instrument

control panel.

Throttle Control Rocker Switch:

 Pressing the throttle

control rocker switch forward will increase the throttle

position. Pressing the throttle control rocker switch backwards

will decrease the throttle position. Always operate at FULL

throttle when mowing.

Fast throttle speed.

Slow throttle speed.

Operation

Before First Time Operation

• Be sure to read all information in the 

Operator

Safety

 and 

Operation

 sections before attempting to

operate this unit. 

• Become familiar with all of the controls and how to stop

the unit. 

• Drive in an open area without mowing to become

accustomed to the unit. 

Summary of Contents for 5901691

















































Reviews: