background image

5100758

Revision G

Rev. Date: 05/2008

TP 100-7299-G-2Z-F

Briggs & Stratton Power Products Group, LLC.
5375 North Main Street
Munnsville, NY 13409
800-933-6175

IS2000Z Series

Zero-Turn Riding Mower

OPERATOR’S

MANUAL

Model Number:

Description

5900619

IS2000ZKAV2561, 25HP, 61” Cut Zero-Turn Riding Mower

5901170

IS2000ZK2761, 27HP, 61” Cut Zero-Turn Riding Mower

5900624

IS2000ZKAV2552, 25HP, 52” Cut Zero-Turn Riding Mower

5900625

IS2000ZK2752, 27HP, 52” Cut Zero-Turn Riding Mower

5900629

IS2000ZLKAV2661, 26HP, 61” Cut Zero-Turn Riding Mower

5900670

IS2000ZBV3061, 30HP, 61” Cut Zero-Turn Riding Mower

5900713

IS2000ZKAV25/52 AUS/NZ, 25HP, 52” Cut Zero-Turn Riding Mower

5900714

IS2000ZKAV25/61 AUS/NZ, 25HP, 61” Cut Zero-Turn Riding Mower

5900715

IS2000ZBV30/61 AUS/NZ, 30HP, 61” Cut Zero-Turn Riding Mower

5900737

IS2000ZKAV2561 CAL, 25HP, 61” Cut Zero-Turn Riding Mower

5900738

IS2000ZBV3061 CAL, 30HP, 61” Cut Zero-Turn Riding Mower

5900750

IS2000ZKAV2761, 27HP, 61” Cut Zero-Turn Riding Mower

5900754

IS2000ZKAV3461SS, 34HP, 61” Cut Zero-Turn Riding Mower

Summary of Contents for 5900619





















































Reviews: