background image

FEATURES

Light weight rechargeable LED headlamp.

TIR optics with flood beam.

DC plug sping cable design for two possiblity to use: 

Battery holder body rear to on head without bag , or 
move the body in bag.

Whole headlamp are strong and confortable.

Cool or neutral white LED version available.

IPX8 Water resistant, 2 Meters waterpoof.

Use 1 x CREE XHP50 LED, Light output of LED is 2300 

lumens.

9 Selectable brightness levels from MIN to MAX and 

Emergency mode (Moonlight).

Smart components and especial auto designed 

provides multiple brightness settings , prevents over-
heat (active temperature control), over discharge and 
wrong polarity of inserted battery protection.

10 

Blinking 10 times to warning indication shows 

the battery level around 20% capacity.

11 

Rubber sleeve holder and comfortable 

headband for reliable fixation.

12 

Aircraft grade hard anodized aluminum alloy for 

lamp & battery holder.

13 

Multi-Power source “5 in 1” is for different 

runtime activities : 1 x 18650 holder / 2 x 18650 
holder(BA2842) / FEREI power pack BP2836B, 
BP4836B and BP6836B.

GENERAL USAGE

The light runs 1 piece 18650 with PCB Li-Ion battery 

or other 3.7V to 4.2V power bank /batteries pack.

Please fully recharge the battery before use.

Brightness level lighting modes:

 

 

Minimum 

 

Medium 

 

Maximum 

 

Emergency mode: 5lm (Moonlight).

Customized brightness settings:

 customized 

brightness setting from LOW to MAX: 25lm / 50lm 
/ 85lm / 150lm / 250lm / 450lm / 850lm / 1500lm, 
8 levels brightness available in all modes except 
Emergency.

Operation:

 to turn on the light , press button switch 

rapidly or continuously to active or convert between 
lighting modes 



 With headlamp already on, 

press and hold on/off button switch to cycle through 
the customized brightness settings from MIN to MAX. 
When a desired brightness appears, simply release the 
switch. To turn off the headlamp, just press the switch 
again after staying at this customized brightness for 
over 3 seconds; But if less than 2 seconds, press the 
switch will be to get conversion between lighting 
modes 



. At the light off, Longer time press the 

button switch (over 2 seconds), the emergency mode 
turn on. To turn off the light, just press the button 
switch again.

Brightness memory:

 In either any lighting mode, 

the brightness could be memorized if staying for over 
3 seconds. Next time you turn on the light again, the 
brightness starts from the memorized lighting mode/

DIAGRAM

brightness. If staying less than 2 seconds at any level 
brightness or mode, press the switch to get conversion 
to next brightness level.

Low battery warning:

 When the battery capaci-

ty gets very low (approx. 20%), the HL65 will emit 10 
successive blinks in 8 seconds. This is a reminder that 
the battery should be recharged or replaced.

Reverse polarity protection: 

When a battery is 

inserted incorrectly,a special protection circuit will acti-
vate and automatically prevent operation to ensure the 
safety of the HL65 and its user.

Over discharge prevention:

 the light will switch 

off automatically in order to prevent damages to 
lithium battery and/or light done by over discharging 
(complete depletion of battery capacity).

Note:

 over discharging lithium batteries might cause 

the battery body to swell up and produce harmful 
gases. In order to avoid this, our product is equipped 
with low voltage circuit break to switch off the light 
when voltage is too low.

INSTALL / REMOVE AND RECHARGE THE BATTERY

Unscrew the flat cap of battery holder.

Put the battery with the correct polarity inside of 

battery holder.

Tighten the flat cap on the screw of battery holder.

Connect the DC plug of AC or DC charger with the 

DC jack of battery.

INSTALL AND CONNECT THE BATTERY HOLDER

Put the 18650 battery holder in to the silicon sleeve, 

as shown in the image above.

Connect the DC plug with DC jack of battery holder, 

and then clockwise to tighten the fixed DC connector, 
as shown in the image above.

MOUNT AND REMOVE HEADBAND

Use the longer headband (about 670mm) pass 

through each side hole of two silicon holder (lamp 
head and battery holder).

The longer headband fix on the adjustment buckle.

Longer piece headband mount finished.

10 

User the shorter headband (about 430mm) pass 

USER MANUAL

HL

65

Light Weight Rechargeable  

LED Headlamp

ADJUSTMENT 

BUCKLE

ADJUSTABLE 

DIRECTION

LED

HEAD

SWITCH

NYLON ELASTIC 

BAND

5.5 DC PLUG

BATTERY BOX 1 X 18650

PHOTOS ARE FOR REFERENCE ONLY. PRODUCTS INKIND PREVAIL!

5

6

7

8

10

9

Reviews: