Fema I4 Series, Manual

Page: 4 / 28

F E MA · MANUFACTURING FOR INDUSTRIAL AUTOMATION 4
Table 2 | Predefined configuration codes - Input / Output
Input Signal
Range
Sensor Output 4/20 mA
Code
Output 0/10 Vdc
Code
See section
...
4/20 mA
Process
010 110
11.1
0/10 Vdc 011 111
0/100 % Potentiometer 012 112
11.2
0/100 % Passive Pot. 013 113
0/1 KOhm
Resistance
014 114
11.3
0/10 KOhm 015 115
0/100 KOhm 016 116
0/1 MOhm 017 117
Reserved 018 to 019 118 to 119
-80/120 ºC Ntc 44004 020 120
11.4
-80/120 ºC Ntc 44005 021 121
-80/120 ºC Ntc 44006 022 122
-80/120 ºC Ntc 44007 023 123
-80/120 ºC Ntc 44008 024 124
-80/75 ºC Ntc 44030 025 125
-80/75 ºC Ntc 44031 026 126
-80/75 ºC Ntc 44032 027 127
-80/75 ºC Ntc 44033 028 128
-80/75 ºC Ntc 44034 029 129
-50/90 ºC Ntc R
25
=10K β=3500 030 130
-200/1200 ºC
Thermocouple J
031 131
11.5
0/700 ºC 032 132
0/400 ºC 033 133
0/250 ºC 034 134
0/150 ºC 035 135
-200/1372 ºC
Thermocouple K
036 136
11.5
0/1200 ºC 037 137
0/700 ºC 038 138
0/400 ºC 039 139
0/300 ºC 040 140
0/250 ºC 041 141
0/150 ºC 042 142
Reserved 043 to 044 143 to 144
-200/1300 ºC
Thermocouple N
045 145
11.5 0/1200 ºC 046 146
0/1000 ºC 047 147
Reserved 048 to 049 148 to 149
8. Predefined configuration codes
Select the desired code for your application, and check the following
sections for more information:
• for information on how to activate a code, see section 13.1
• to customize the input and output signals, see section 13.6
Notes
• Code ‘ uSEr ’ indicates that a user custom configuration is active, and it does not
match any of the listed codes This code is non-selectable, for information only.
Example: select code ‘
011 ’ for 0/10 Vdc=4/20 mA, the instrument reads code ‘ 011 ’.
Later, configure the input to 0/7 Vdc=4/20 mA, this does not match a listed code, and
the instrument reads ‘ uSEr ’. Or change the output to 0/10 Vdc=1/5 Vdc, this does not
match a listed code, and the instrument reads ‘ uSEr ’.
• Code ‘ ---- ’ identifies the end of the list, it follows code ‘ 199 ’ and the list
continues with code ‘ 010 ’. Select ‘ ---- ’ to exit the list without applying changes.
Table 2 | Predefined configuration codes - Input / Output
Input Signal
Range
Sensor Output 4/20 mA
Code
Output 0/10 Vdc
Code
See section
...
-200/1000 ºC
Thermocouple E
050 150
11.5
0/1000 ºC 051 151
0/800 ºC 052 152
0/500 ºC 053 153
0/300 ºC 054 154
-200/400 ºC
Thermocouple T
055 155
11.5
0/400 ºC 056 156
0/300 ºC 057 157
0/200 ºC 058 158
-50/1768 ºC
Thermocouple R
059 159
11.5 0/1600 ºC 060 160
0/1000 ºC 061 161
-50/1768 ºC
Thermocouple S
062 162
11.5
0/1600 ºC 063 163
0/2320 ºC
Thermocouple C
064 164
11.5
0/1500 ºC 065 165
250/1820 ºC Thermocouple B 066 166 11.5
Reserved 067 to 069 167 to 169
-200/850 ºC
Pt100
(2 and 3 wires)
070 170
11.6
0/600 ºC 071 171
0/400 ºC 072 172
0/300 ºC 073 173
0/200 ºC 074 174
0/100 ºC 075 175
-50/+50 ºC 076 176
Reserved 077 to 079 177 to 179
-200/850 ºC Pt500 080 180
11.6
-200/850 ºC Pt1000 081 181
Reserved 082 to 099 182 to 199
(End of list) ‘----’ (see notes below)
(Custom selection) ‘ uSEr ’ (see notes below)