240613DT
Red Knob ‘HOT’ Compression Spring
Blue Knob ‘COLD’
ISOLATOR
MIXER BODY
Rotor
Shut-off Seals
Clip
Groove
Filters
Isolator
O-Ring
Brass Nipple
Stainless
Steel Clip
Grub Screw
Wallplate
Rotor O-Ring Seals
Handle
Control Sleeve
Shower Stem O-Ring
Shower Head Stem
Shower Head
SERVICE NOTES
Use only
GENUINE FELTONMIX R
eplacement Parts
To Replace Seals and Springs
A rubber shut-off seal and spring is fi tted in each
of the two inlets of the valve body and two O-ring
seals fi tted to the rotor located inside the valve
body.
1. Unscrew shower head and stem from valve
body.
2. Using both hands support the handle top and
bottom and withdraw from valve body.
3. Remove wallplate by unscrewing the two
11⁄8 x 7 fi xing screws.
4. Turn off water supply at either the mains or
the shower mixer isolators.
5. Gently prise stainless steel retaining clips on
valve body outwards with screwdriver and
remove clips completely. Pull isolators clear
of valve body.
6. Unscrew mixer retaining screws and remove
mixer from wall.
7.
Remove grub screw from control sleeve.
8. Withdraw rotor from body using a suitable
tool through cross hole in rotor.
9. Using seal extractor tool supplied with the
replacement seal pack, insert end marked
'REMOVE' fully into hole in centre of seal
and withdraw seal and spring.
10. Fit blade of seal extractor tool end marked
'REPLACE' into slots in bore of new seal and
spring.
11. Fit seal in inlet bore with turning motion until
lugs on seal engage in slots in bore of inlet.
Push fully home.
12. Discard O-Ring seals on rotor. Replace with
new O-Ring seals.
13. Discard isolator O-Rings and fi t new O-Rings
supplied.
14. Re-assemble in reverse manner. Insert rotor
in body. Fit isolators to mixer body. Insert
stainless steel retaining clips through slots
In valve body and press fully home
Filters
Each isolator is fi tted with a fi lter. These fi lters can
be easily prised out, cleaned and snapped back
into place.
Felton
mix
The Perfect Shower Every Time
SHOWER MIXING VALVES
Felton Industries Ltd warrant to the purchaser of this shower mixer
that it is free from defects in materials and workmanship. Accordingly
we undertake to repair or replace and part which we are satisfi ed is
defective for up to fi ve years after installation date. This warranty is
valid only when the mixer is installed by a qualifi ed plumber, to the
following instructions.
Felton Industries Limited is an IS09002 Registered Supplier, and
Feltonmix
®
shower valves are manufactured to WaterMark standard
AS/NZS 3718:2005, Licence No. WMKA25208 and New Zealand
Standard 4611: 1982, Licence No. 2491.
Three models are available to suit different conditions. Filters are fi tted
to protect parts from damage caused by water born particles. Removal
of these fi lters may void the warranty.
The maximum hot water temperature should not exceed 80ºC
Feltonmix
®
Type U
- Blue Rotor.
For use on unequal supply pressures. Mains pressure cold
i.e.
supplies from 150 kPa to maximum 500kPa ; low pressure hot
i.e.
minimum of 20 kPa to maximum 150 kPa fl ow pressure.
Feltonmix
®
Type H
- Pink Rotor.
For use on equal high supply pressures. Mains pressure hot and cold
i.e.
supplies from 150 kPa to maximum 500kPa fl ow pressure.
Feltonmix
®
Type E
- Green Rotor.
For use on equal low supply pressures. Hot and cold supply from
minimum 20 kPa to maximum 150 kPa.
Note: A pressure reducing valve in compliance with AS 1357 may
need to be fi tted to maintain supply pressure below 500 kPa.
