background image

Page 8

Step #9: remove cable management covers 

•  To remove the cover from the motion arms, slide the cable cover  

upward. 

•  To remove the cover from the fixed arms, arm stems and stubby arm,  

slide the cable cover out.

Step #10: install lockout set screws, if desired

Default rotation of the fixed arms and motion arms is 360°. Installation of a lockout set screw limits rotation to 180°.  
There is no lockout provision for the stubby monitor arm.

•  To lockout rotation of the fixed or motion arms, install an M4x15 set screw in the underside of the arm stem. Tighten the screw, then back it off one turn.

 

— Installing a set screw in the front hole allows 180° rotation to the right only. A set screw in the rear hole allows 180° rotation to the left only.

 

— In the example below, to prevent the fixed arms from rotating to the rear (a left rotation with the left arm and  a right rotation with the right arm),  

install a set screw in the front hole on the left arm stem and the rear hole on the right. The motion arms are allowed their full 360° of rotation.

•  The fixed arm or motion arm must be in its allowed range of rotation when installing the lockout set screw. 

 

KataEX3-FMS 

Assembly

front

rear

set screw

M4x15

2mm

Allen key

front

rear

180°

180°

360°

360°

monitors

not shown

stubby

monitor arm

not shown

slide out

slide out

fixed arm

arm stem

stubby arm

slide up

motion arm

Summary of Contents for ESI Kata EX3-FMS Series













Reviews: