background image

Page 18

Step #13: make any necessary adjustments 

Depending on the configuration, there are up to seven possible ways to adjust and change the position of the monitors to maximize the efficiency 

and comfort of the working environment. The illustration of a KataEX3-FMS configuration on the following page shows all seven ways. Five types of 

adjustments are shown in the illustration below of a KataEX2-FF configuration with VESA mounts attached to fixed arms.

1. 

Slider mount only: 

Monitor position on slider

 

— To move the monitor from side-to-side, use the 2mm end of the dual Allen key to loosen the set screw (M4x9) on the bottom of the VESA mount assembly, then slide 

the monitor along the slider bar. Do not loosen the set screw more than one full turn — the tip of the set screw must remain inside the groove on the slider bar so 

that the mount assembly cannot slide off the ends. Re-tighten the set screw when the monitor is positioned where desired.

2. Monitor tilt

 

— Use the 4mm end of the dual Allen key

 

to loosen the screw on the side of the VESA mount to change monitor tilt angle. Tighten the screw to hold the angle.

3. Monitor swivel

 

— Use the 4mm end of the dual Allen key

 

to adjust the underside screw behind the VESA mount  or slider mount for the desired ease of monitor rotation.

4. Head adapter

 

— Use the 4mm end of the dual Allen key

 

to adjust the underside screw at the end of the arm stem for the desired ease of head adapter rotation. In effect, this is the 

same as the monitor swivel adjustment. Head adapters are used to attach monitors to fixed arms and stem arms. 

5. Motion arm weight

 

— Use the 4mm end of the dual Allen key

 

to adjust the screw at the end of the motion arm for the appropriate monitor weight. When adjusted properly, the monitor 

weight is balanced, making it easy to raise or lower the monitor. 

6. Motion arm swivel

 

— Use the 4mm end of the dual Allen key

 

to adjust the screw in the underside of the arm stem or fixed arm for the desired ease of motion arm rotation. 

7. Fixed arm swivel

 

— Use the 4mm end of the dual Allen key

 

to adjust the underside screw at the end of the arm stem or inner fixed arm for the desired ease of fixed arm rotation.

 KataEX 

Adjustments

behind

VESA plate

2

7

monitors

not shown

3

outer

fixed arm

inner

fixed arm

4

7

head

adapter

KataEX2-FF

Summary of Contents for esi Kata EX Series





















Reviews: