2
Manual Version 1.0
飞宇科技 SmartStab 两轴手机自拍稳定器是一款
专为智能手机打造的轻量型可穿戴式摄影稳定器,
体积小巧,兼容性高,应用广泛。适用于
iPhone 6s Plus / 6s / 6 Plus / 6 / 5c / 5s / 5 / 4s / 4
以及类似尺寸的智能手机。
SmartStab 两轴手机自拍稳定器具有高兼容性,标
配T型夹头可通配T型连接底座的配件。自带1/4英
寸螺丝孔位,可直接将稳定器安装至带有1/4英寸
螺丝的配件
简 介
安 装
1
FY SmartStab 2-Axis Selfie Gimbal for
Smartphone is a lightweight, yet feature-rich,
SmartStab 2-Axis Selfie Gimbal for Smartphone
capable of capturing immersive and fully
stabilized footages. It is compatible with iPhone
6s Plus / 6s / 6 Plus / 6 / 5c / 5s / 5 / 4s / 4 and
other smartphone with similar dimensions.
The FY SmartStab 2-Axis Selfie Gimbal for
Smartphone is a high compatibility gimbal, the
T-Clamp adapter is packaged with every gimbal.
Users can attach the gimbal to any accessories
with the T-Clamp .
The SmartStab 2-Axis Selfie Gimbal for
Smartphone also contains two 1/4"-20 tripod
mounts on its gimbal body, allowing the gimbal
to be mounted in different orientations to all
universal tripod screw mount accessories.
Do not power on the gimbal before completing all the installation steps.
Extension bar with control function
Connect the control cable of the extension bar to the function interface of
the Gimbal, the tilting of the gimbal can be controlled during normally
working .
SmartStab 2-Axis Selfie Gimbal for Smartphone compatible with iPhone 6s Plus / 6s / 6 Plus / 6 / 5c / 5s / 5 / 4s / 4
and other smartphone with similar dimensions
180°
180°
将手持延长杆控制线的接头接到稳定器的功能端口,可在稳定器正常工作下实现
对俯仰轴的俯仰控制。
带控制功能的延长杆
Extension bar
with control function
带控制功能的延长杆
Phone quick-release
adapter
手机夹具
1
2
Introduction
Install
SmartStab 两轴手机自拍稳定器适用于 iPhone 6s Plus / 6s / 6 Plus / 6 / 5c / 5s / 5 / 4s / 4 以及类似尺寸的智能手机
SmartStab 两轴手机自拍稳定器
装入电池
安装手机
拧开电池盖,装入2节16340电池后拧紧螺丝。
拉开手机夹,将夹具上端向上拉至稍微
超过手机的高度,将手机夹紧。如图所示。
开机与关机
调整手机位置及安装配重盖
为了让稳定器保持最佳工作状态,安装时,请尽量保持
稳定器通电前手机与俯仰轴的平衡,如图。如经调整后
仍无法平衡,向手机端方向倾斜,请选用配重块。
注 意 !
WARNING !
!
请先安装好适合尺寸的手机后,再通电!
Remove the screws on the battery compartment,
insert two16340 batteries
and tighten the screws.
Attach the Phone by the quick-release
adapter, and ensure it is secure.
Install the batteries
Install the phone
If the smartphone inclines towards the tilting axis,
pull it towards the left to be in place, and let the
center of gravity keep balance or slightly incline
to the smartphone . If the smartphone still inclines
towards the tilting axis, install the counter-weight.
Adjust the phone position
and install the counter-weight
Powering ON / OFF
SmartStab 2-Axis Selfie Gimbal for Smartphone
1
2
4
3
开机:
检查相机是否安装稳固后,长按功能键
2秒,稳定器随即开启。
关机:
长按功能键3秒即关机。
Power on:
Ensure the camera is mounted
securely, then hold down the function button
for 2 seconds to turn on the gimbal.
Power off:
Hold down the function button
for 3 seconds to turn off the gimbal.
Function
Interface
功能端口
功能端口
Function Interface
Micro Port
俯仰
Tilting
俯仰轴
Tilting Axis
航向轴
Panning Axis
功能键
Function Button
航向
Panning
延长杆控制线
Control Cable
向上控制按键
Up Button
向下控制按键
Down Button
Connect Way
连接方式
短杆手拧螺丝
Short Screw
电池盖螺丝
screws on the
battery compartment
* 本产品不包含手机
* Smartphone excluded
Tilting Axis
俯仰轴