manualshive.com logo in svg

Federal Signal Corporation SS2000+ ? Series, Operation Manual, Page: 67 / 80

Share
Download
Federal Signal Corporation SS2000+ ? Series Operation Manual Download Page 67

67

Replacement Parts

Description, Specifications, SS Software, and Operation Manual

 

Federal Signal

 www.fedsig.com

Clicking OK activates the system. If you are not sure or do not have authorization 

to activate the system, click Cancel. When the command is received a “Button 

Sent” status message displays in the blue caption bar at the top of the screen. 

This confirms the received the command, but does not verify siren 

operation. To verify siren operation the system must be polled from a Commander 

station.

Logging Out of the Web Interface

Use the Log Out page to log out before the five minute session timer expires.
To log out of the web interface:
1.  Select Log Out. 

The Log Out page appears.

2.  Click the Log Out button to logout.

Replacement Parts

To order replacement parts, see Getting Service.

Table 10 Replacement Parts

Description

Part Number

Power Supply with US Cable Q-SSPWR
UK 240 Vac Power Cable

Q17501252A

EU 240 Vac Power Cable

Q17501253A

Kenwood

®

 Radio Cable

Q17500863-01

Getting Service

If you are experiencing any difficulties, contact Federal Signal Customer Support at  

800-548-7229 or 708-534-3400 extension 7511 or Technical Support at 800-524-3021 

or 708-534-3400 extension 7329 or through email at [email protected]. For 

instruction manuals and information on related products, visit http://www.fedsig.com/

Summary of Contents for SS2000+ ? Series

















































































Reviews:

No comments