manualshive.com logo in svg

Federal Signal Corporation SS2000+ ? Series, Operation Manual, Page: 65 / 80

Share
Download
Federal Signal Corporation SS2000+ ? Series Operation Manual Download Page 65

65

Web Browser Activation

Description, Specifications, SS Software, and Operation Manual

 

Federal Signal

 www.fedsig.com

Restoring Configuration to Factory Defaults

You can restore the factory default settings with or without restoring the network 

parameters. The Activation Button configuration will not change when a Factory Default is 

performed.
The RTU must reboot to begin using the new settings. Use the Reboot web page to 

reboot the RTU.

Default Settings

RTU Number: 900

Description: my description

SmartMsg disabled

Modbus disabled

Smartmsg Server: 10.10.10.10

IP Address: 10.10.10.1

Subnet Mask: 255.255.0.0

Default Gateway: 10.10.10.10

Primary/Secondary DNS: 0.0.0.0/0.0.0.0

Admin user name: admin

Admin user password: fedsig

User 1 - User 4 username/password: blank

Factory Support User: Enabled

To restore configuration to factory defaults:
1.  Select Factory Defaults. 

The Factory Defaults page appears.

Field

Description

Include Network 

Parameters

Check the box to include network parameters. 

NOTE:

 This changes the IP address of the RTU to factory 

default settings and make the device inaccessible over a 

production network.

Summary of Contents for SS2000+ ? Series

















































































Reviews:

No comments