manualshive.com logo in svg

Federal Signal Corporation SS2000+ ? Series, Operation Manual, Page: 52 / 80

Share
Download
Federal Signal Corporation SS2000+ ? Series Operation Manual Download Page 52

52

  

  

Hotkey Activation

Series C 

Federal Signal www.fedsig.com

Menu Selection

The following section explains how the use the menu section.
To view the menu selection, press the MENU button.
The LCD displays the following.

1. Printer Status

2. Send Calibrate

3. Set Date and Time

4. Test Mode

The following table describes the menu features.

Menu Number

Description

1. Printer Status

Displays the current printer status: Printer Off, No Paper, 

Printer Offline, Printer Error, or Printer OK.

2. Send Calibrate

Sends the calibration tone.

3. Set Date and Time

Sets the date and time.

4. Test Mode

Begins the self test.

Sending the Calibration Tone

To send the calibration tone:
1.  Press the MENU button. 
2.  Press 2.

The LCD displays the following:

SEND to Transmit

CAL 

   STANDBY

3.  Press SEND. The transmits a 10 second, 1 kHz sinewave. This sets 

transmitter deviation.

The LCD displays the following.

SEND to Transmit

Sending

Summary of Contents for SS2000+ ? Series

















































































Reviews:

No comments