Federal Signal Corporation SmartSiren Platinum SSP3000B Installation And Maintenance Instructions Manual Download Page 15

Page: 15 / 60

An Overview of the SmartSiren Platinum

Installation and Maintenance Instructions

Federal Signal www.fedsig.com

Table 6 SSP3000B kit contents

Qty. Description

Part Number

SSP3000B Control Head

853600632

SSP3000B Siren Amplifier/Relay Module

853600629

Cable Assembly, RS485, 25 ft

1751357-02

Cable Assembly, Control

17500307

Cable Assembly, Auxiliary Relay

1751541

Cable Assembly, RJ45 Ethernet Crossover

1751532

Cable Assembly, SignalMaster

™

and Inputs

1751542-01

Cable Assembly

17500308

Cable Assembly, RJ45, Ethernet Crossover

1751532

Bracket, Mounting, Control Head

85361065

Screw, Mach. Pan Head, #6-32

7000A404-05

Screw, Cap, Hex Head, 1/4"-20

7002A000-12

Screw, Pan Head, #10, Thread-Forming

7011A047-08

Lock Washer, Split, #6

7074A001

Lock Washer, Ext, Tooth, 1/4"

7075A007

Keyhead Legends, Scored Sheet

8572294

Microphone with Modular Plug

256B577-03

Fuse, 5 A, Mini Blade, LED Indicator

148210-04

Fuse, 10 A, Mini Blade, LED Indicator

148210-06

Fuse, 20 A, Mini Blade, LED Indicator

148210-08

Quick Connect Guide

25600152

Quick Reference Guide

2562503

Card, Safety Instructions

256B691

Instruction Sheet, Operators Safety Messages

256A692

Label, Warning, Siren/Speaker

1612339

Summary of Contents for SmartSiren Platinum SSP3000B




























































Search results

Summary of Contents for SmartSiren Platinum SSP3000B

Reviews:

Related manuals for SmartSiren Platinum SSP3000B

Brands by name

Popular brands

Federal Signal Corporation SmartSiren Platinum SSP3000B, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for SmartSiren Platinum SSP3000B

Reviews:

Related manuals for SmartSiren Platinum SSP3000B

Brands by name

Popular brands