Federal Signal Corporation SLR LED Installation And Maintenance Manual Download Page 2

Page: 2 / 20

blank page

Limited Warranty

This product is subject to and covered by a limited warranty,

a copy of which can be found at www.fedsig.com/SSG-Warranty.

A copy of this limited warranty can also be obtained by written

request to Federal Signal Corporation, 2645 Federal Signal Drive,

University Park, IL 60484, email to [email protected] or

call +1 708-534-3400.

This limited warranty is in lieu of all other warranties, express or

implied, contractual or statutory, including, but not limited to the

warranty of merchantability, warranty of fitness for a particular

purpose and any warranty against failure of its essential purpose.

2645 Federal Signal Drive

University Park, Illinois 60484
www.fedsig.com

Customer Support

Police/Fire-EMS:

800-264-3578 • +1 708 534-3400

Work Truck:

800-824-0254 • +1 708 534-3400

Technical Support

800-433-9132 • +1 708 534-3400

All trademarks are property of their respective owners.

Summary of Contents for SLR LED




















Search results

Summary of Contents for SLR LED

Reviews:

Related manuals for SLR LED

Brands by name

Popular brands

Federal Signal Corporation SLR LED, Installation And Maintenance Manual

Search results

Summary of Contents for SLR LED

Reviews:

Related manuals for SLR LED

Brands by name

Popular brands