2562366A
REV. A 1007
Printed in U.S.A.
INSTALLATION AND MAINTENANCE INSTRUCTIONS
FOR
ARJENT® S2 SERIES B LED/HALOGEN LIGHT ASSEMBLY
SAFETY MESSAGE TO INSTALLERS
OF
FEDERAL SIGNAL LIGHT SYSTEMS
People’s lives depend on your safe instal-
lation of our products. It is important to
read, understand and follow all instructions
shipped with the products. In addition, listed
below are some other important safety in-
structions and precautions you should follow:
• To properly install a light assembly: you must
have a good understanding of automotive
electrical procedures and systems, along with
proficiency in the installation and use of safety
warning equipment.
• When installing equipment or wiring inside air
bag equipped vehicles, the installer MUST en‑
sure that the equipment or wiring is installed
ONLY in areas recommended by the vehicle
manufacturer. Failure to observe this warn‑
ing will reduce the effectiveness of the air bag,
damage the air bag, or potentially damage or
dislodge the equipment, causing serious injury
or death to you or others.
• When drilling into a vehicle structure, be sure
that both sides of the surface are clear of any‑
thing that could be damaged.
• A light system is a high current device. In
order for it to function properly, a separate
ground connection must be made. If practical,
it should be connected to the negative battery
terminal. At a minimum, it may be attached
to a solid metal body or chassis part that will
provide an effective ground path as long as the
light system is to be used.
• Locate light system controls so the VEHICLE
and CONTROLS can be operated safely under
all driving conditions.
• This product contains high intensity LED de‑
vices. To prevent eye damage, DO NOT stare
into the light beam at close range.
• You should frequently inspect the light system
to ensure that it is operating properly and that
it is securely attached to the vehicle.
• File these instructions in a safe place and refer
to them when maintaining and/or reinstalling
the product.
Failure to follow all safety precautions and
instructions may result in property damage, serious
injury, or death to you or others.
I.
UNPACKING.
After unpacking the Arjent S2 lightbar, inspect it for
damage that may have occurred in transit. If the unit has
been damaged, file a claim immediately with the carrier,
stating the extent of damage. Carefully check all envelopes,
shipping labels and tags before removing or destroying
them.
II. DESCRIPTION.
The Arjent S2 lightbar is available in either a 36”, 44”
or 53” length and operates on a nominal input of 13.6 volts
DC (11 volts DC minimum). Clear polycarbonate bases
along with clear or colored polycarbonate domes house a
multi‑channel programmable (via serial interface module)
circuit board assembly within the bar. The multi‑channel
PCB assembly is connected in turn to additional multiple
circuit board panels, each having the availability of 4 to 5
maximum factory‑installed options per panel. The lightbars
have an operating temperature range of ‑30°C to +65°C
(‑22°F to +149°F). They may be mounted with a hook,
permanent, or flat mounting kit to the vehicle. Available
built to order options on the Arjent S2 include:
Panelized Solaris LED Options:
XD1LC6‑A, ‑R, ‑B, ‑W, ‑G: 6‑button Solaris S2 LED
light head
XDALED‑A, ‑R, ‑B, ‑W, ‑G: 3‑button Solaris S2 LED
light head, alley light position (factory default at front
light cutoff)
• Flashing pattern selectability of the LED options
may be specified via programming of the lightbar.
See table 2.
• SignalMaster operation is accomplished via
programming of the lightbar.
4‑pos. SignalMaster available on the 36” bar;
6‑pos. SignalMaster available on the 44” bar;
8‑pos. SignalMaster available on the 53” bar
• Steady‑burn availability of 1 or 2 front LED
heads must be specified via the Arjent S2 initial
order entry.
Panelized Halogen Options (maximum of 6 per
lightbar):
XDAHAL
Alley Light, 35 watts/head (MR 11)
adjustable
XDTD
Takedown Light 50 watts/head
XDWL
Work Light 50 watts/head
• Flashing of the halogen options is accomplished via
programming of the lightbar.
Mounting Options:
XAHKN‑SC, XAHK‑SC
Hook Mount, Neutral or
Black
XAPKN‑SC, XAPK‑SC
Permanent Mount, Neutral
or Black
XAFM
Flat Mount
