manualshive.com logo in svg

FDE SO-CONNECT PID, User Manual

Share
Download
FDE SO-CONNECT PID User Manual Download Page 21

Partie II 

–

 Starting the pump 

 

21 

Battery charging 

When you need to recharge a battery, please follow the instructions below: 

▪

 

First connect the power cord to the charger, then to the power socket. 

▪

 

Insert the battery in the charger. The battery label must be turned towards the front of the charger. 

▪

 

If a problem occurs during charging, disconnect the charger from the wall socket immediately in order to stop the power supply. 

▪

 

Do not place the charger in areas that are very hot or cold, dusty or dirty, humid or subject to heavy vibrations. 

 

 Precautions 

▪

 

Make sure you always use the battery charger supplied with the 

SO

♥

CONNECT PID

 pump only. Using another type of charger 

may damage the battery. 

 

 Comments 

▪

 

The charger will heat up slightly while in use. This is not a sign of malfunctioning. 

 

The light on the charger shows the battery charge status. 

 

 

Flashing 

yellow 

or steady 

yellow

: charging in progress. 

 

Steady 

green 

light: battery fully charged 

 

Flashing 

green 

light: battery not connected 

 

Flashing 

red 

light: error 

 

 

 

Summary of Contents for SO-CONNECT PID












































































Reviews:

No comments

Brands by name

Popular brands

Load more brands