FDC ENIGMA II SLIMLINE Owner'S Manual Download Page 3

LT4934 (1:01/08) 

3

ENIGMA II SLIMLINE 

Users Instructions

 

 

SECTION ONE 

Important Information

 

Consumer Protection Information 

As manufacturers and suppliers of heating products, we take every care, as far as is reasonably 
practicable, that these products are so designed and constructed as to meet the general safety 
requirement when properly used and installed. To this end, our products are thoroughly tested 
and examined before despatch. 
 

IMPORTANT NOTICE:

 Any alteration that is not approved by the appliance manufacturer could 

invalidate  the  approval  of  the  appliance,  operation  of  the  warranty  and  could  affect  your 
statutory rights.

 

 

Health and Safety otice 

Important 

This appliance  could  contain  some  of  the materials,  indicated below,  that  could be  interpreted 
as being injurious to health and safety. It is the users / installers responsibility to ensure that the 
necessary  personal  protective  clothing  is  worn  when  handling  these  materials,  see  below  for 
information. 

 

Artificial Fuels, Mineral Wool, Insulation Material, Refractory/Ceramic Fibres, Glass Yarn - 

may be harmful if inhaled, may be irritating to skin, eyes, nose and throat.  

When  handling

 

avoid  inhaling  and  contact  with  skin  or  eyes.  Use  disposable  gloves, 

facemasks and eye protection. After handling wash hands and other exposed parts. If a vacuum 
is used for cleaning the coals or cleaning after servicing / installation it is recommended that it 
be of the type fitted with a HEPA filter

Disposal  of  refractory/ceramic  materials

To  keep  dust  to  a  minimum  these  materials 

should  be  securely  wrapped  in  polythene  and  be  clearly  labelled  ‘RCF  waste’.  These 
materials  are  not  classified  as  ‘hazardous  waste  and  should  be  disposed  of  at  a  site 
licensed for the disposal of industrial waste. 

 

 

• 

The ENIGMA II SLIMLINE is a decorative fuel effect appliance with a radiant heat conserver 
box for improved efficiency.  

• 

This appliance is intended for decorative purposes. 

• 

The ENIGMA II SLIMLINE is designed and tested to the requirements of the EN 509. 

• 

The appliance is for use on Natural Gas only and should be installed by a competent person 
i.e.  CORGI-registered,  in  accordance  with  the  GAS  SAFETY  (INSTALLATION  AND  USE) 
REGULATIONS. 

• 

The  chimney  or  flue  (unless  new  or  previously  used  with  a  gas  appliance)  must  be  swept 
before installation if it has been used for solid fuel. 

 

WARNING 

 

This  appliance  has  a  naked  flame,  as  with  all  such  fires  it  is  recommended  that  a  fireguard 
should be used for the protection of children, the elderly and infirm.  Fireguards should conform 
to BS 6539 (1984) (Fireguards for use with solid fuel appliances).   
 
 
 

Summary of Contents for ENIGMA II SLIMLINE

























Reviews: