Fayat DYNAPAC DFP8 Operatinginstructions And Maintenance Download Page 26

Page: 26 / 110

3.4.4 Safety regulations and environmental protection regulations for handling oil

WARNING!
Danger of burning by ignited oil!

–

Do not allow oil to come into contact with hot

components.

–

Smoking and open fire is prohibited!

–

Wear your personal protective equipment (pro-

tective gloves, protective clothing).

CAUTION!
Health hazard caused by contact with oil!

–

Wear your personal protective equipment (pro-

tective gloves, protective clothing).

–

Do not inhale any oil vapours.

–

Avoid contact.

CAUTION!
Danger of slipping on spilled oil!

–

Immediately bind spilled oil with an oil-binding

agent.

ENVIRONMENT!
Oil is an environmentally hazardous substance!

–

Always keep oil in proper containers.

–

Immediately bind spilled oil with an oil-binding

agent.

–

Dispose of oil and oil filter according to regula-

tions.

Fig. 5

Concerning your safety – Handling fuels and lubricants

DFP8

Summary of Contents for DYNAPAC DFP8















































































































Search results

Summary of Contents for DYNAPAC DFP8

Reviews:

Related manuals for DYNAPAC DFP8

Brands by name

Popular brands

Fayat DYNAPAC DFP8, Operatinginstructions And Maintenance

Search results

Summary of Contents for DYNAPAC DFP8

Reviews:

Related manuals for DYNAPAC DFP8

Brands by name

Popular brands