Fayat DYNAPAC DFP8 Operatinginstructions And Maintenance Download Page 25

Page: 25 / 110

3.4.3 Safety regulations and environmental protection regulations for handling fuel

stabiliser

WARNING!
Danger of burning by ignited fuel stabilizer!

–

Do not allow fuel stabilizer to come into contact

with hot components.

–

Smoking and open fire is prohibited.

WARNING!
Health hazard caused by contact with fuel sta-

bilizer!

–

Wear your personal protective outfit (protective

gloves, protective clothing).

–

Do not inhale any fuel stabilizer fumes.

–

Do not swallow fuel stabilizer.

–

Avoid contact with fuel stabilizer.

ENVIRONMENT!
Fuel stabilizer is an environmentally hazardous

substance!

–

Immediately bind spilled fuel stabilizer with an

oil-binding agent and dispose of according to

regulations.

–

Dispose of fuel stabilizer according to regula-

tions.

Concerning your safety – Handling fuels and lubricants

DFP8

Summary of Contents for DYNAPAC DFP8















































































































Search results

Summary of Contents for DYNAPAC DFP8

Reviews:

Related manuals for DYNAPAC DFP8

Brands by name

Popular brands

Fayat DYNAPAC DFP8, Operatinginstructions And Maintenance

Search results

Summary of Contents for DYNAPAC DFP8

Reviews:

Related manuals for DYNAPAC DFP8

Brands by name

Popular brands