background image

Introduction

4812159601_H.pdf

2021-01-14

Inspect the machine every day, before starting.
Inspect the entire machine so that any leakages or
other faults are detected.

Check the ground under the machine. Leakages are
more easily detected on the ground than on the
machine itself.

If faults or suspected damage are detected on the
roller, contact the responsible supervisor for any action.

THINK ENVIRONMENT ! Do not release oil,
fuel and other environmentally hazardous
substances into the environment. Always send
used filters, drain oil and fuel remnants to
environmentally correct disposal.

THINK ENVIRONMENT ! Do not release oil,
fuel and other environmentally hazardous
substances into the environment. Always send
used filters, drain oil and fuel remnants to
environmentally correct disposal.

This manual contains instructions for periodic
maintenance, where maintenance after every 10 and
50 hours of operation can be performed by the
machine operator. Other maintenance intervals must
be carried out by accredited (Dynapac) service
personnel.

Additional instructions for the engine can be
found in the manufacturer's engine manual.

Additional instructions for the engine can be
found in the manufacturer's engine manual.

Specific maintenance and checks on diesel
engines must be performed by engine supplier
authorized personnel.

Specific maintenance and checks on diesel
engines must be performed by engine supplier
authorized personnel.

CE marking and Declaration of conformity

(Applies to machines marketed in EU/EEC)

This machine is CE marked. This shows that on
delivery it complies with the basic health and safety
directives applicable for the machine in accordance
with machinery directive 2006/42/EC and that it also
complies with other regulations and directives
applicable for this machine.

A "Declaration of conformity" is supplied with this
machine, which specifies the applicable regulations
and directives with supplements, as well as the
harmonized standards and other regulations that are
applied and according to the regulations must be
declared in writing.

3

Summary of Contents for DYNAPAC CC2200















































































































































































Reviews: