manualshive.com logo in svg

Fayat Group CP1200, Instruction Manual, Page: 34 / 86

Share
Download
Fayat Group CP1200 Instruction Manual Download Page 34

 

A/C 

– System operation 

 

30 

4812325556EN 

08/01/2023 

 

A/C System Operation - Cab 

 

 

 

No.

 

DESIGNATION

 

SYMBOL

 

FUNCTION

 

1 

Front wiper switch 

 

Press to operate the front windshield 
wiper. 

2 

Rear wiper switch 

 

Press to operate the rear windshield 
wiper. 

3 

Front and rear windshield 
washers 
switch 

 

Press the top to activate the front 
washers. Press the bottom to activate 
the rear washers. 

4 

Fuse box 

 

Contains fuses from the electric 
system in the cab. 

5 

Automatic Climate Control 

- 

Air conditioning automatic control. 

6 

Air outlets 

- 

Direct the air outlets to obtain better 
ventilation. 

7 

Emergency exit hammer 

 

 
If it is necessary to leave the cab 
during an emergency, release the 
hammer and break the right-side 
windows. 

8 

Potentiometer with knob 

 

Adjust to operate the front windshield 
wiper. 

Summary of Contents for CP1200























































































Reviews:

No comments