Fayat Group Bomag BVT 65 Operating Instruction, Maintenance Instruction Download

Page: 62 / 97

8.2.2.2

Fuel stabilizer

If the machine is only occasionally used (if it is out of use for longer

than four weeks), mix in the correct amount of fuel stabilizer

directly after you have purchased fresh fuel.

The fuel stabilizer has a limited shelf life.

Please follow the instructions of the manufacturer concerning the

correct mixing ratio and shelf life.

Mixing in fuel stabilizer does not regenerate old fuel.

8.2.3 Gear oil SAE 75W-90

Use a fully synthetic gear oil in accordance with SAE 75W-90,
API GL5 with a kinematic viscosity of at least 16 mm

/s at 100 °C

(212 °F).

Maintenance – Fuels and lubricants

BVT 65

Go to

Discount-Equipment.com

order your parts

Summary of Contents for Bomag BVT 65


































































































Search results

Summary of Contents for Bomag BVT 65

Reviews:

Related manuals for Bomag BVT 65

Brands by name

Popular brands

Fayat Group Bomag BVT 65, Operating Instruction, Maintenance Instruction

Search results

Summary of Contents for Bomag BVT 65

Reviews:

Related manuals for Bomag BVT 65

Brands by name

Popular brands