background image

 

 

Thank you for purchasing FATEK HMI. Before installing or operating the unit, please 

read this installation guide carefully to ensure correct use. 

 

1. Safety Precautions 

(Read these precautions before use.)

 

1.1 General 

z

  Unpack and check the delivery for transportation damage. If any damage or 

deformation is found, please notify the supplier. 

z

  The supplier is not responsible for the disassembled, altered or modified 

device. 

z

  Never allow fluid or any conductive particles to enter into the HMI. 

Otherwise, it may damage the HMI, cause fire or malfunction. 

z

  Only qualified personnel may install the HMI, perform maintenance and 

inspection. 

z

  The liquid crystal inside the LCD panel is a hazardous substance. If the 

panel is damaged, avoid contact with the leaked liquid crystal. If the liquid

crystal spills on clothing or skin, use soap and wash off thoroughly. In case 

of eye contact the liquid, hold the eye open, flush with plenty water and get 

medical attention as soon as possible. 

z

  Do not touch any terminals while the power is on. Otherwise, it may cause 

injury due to electrical shock. 

z

  Disconnect the power supply before installing the HMI, do wiring operation, 

perform maintenance or inspection. Otherwise, it may cause damage or

electrical shock. 

1.2 Installation 

z

  The installation may be carried out by

 

qualified

 

personnel

 

only.

 

z

  Install the HMI according to the installation procedures. 

z

  Check the power source voltage is within the specified range and the

polarity is correct before connecting the HMI

.

 

z

  Keep signal and power supply cables away from high-voltage, large-current 

carrying cables. 

P5102S/N/N1 HMI Installation Guide

 

R

Summary of Contents for P5102S









Reviews: