Faro FaroArm Fusion Manual Download Page 84

Page: 84 / 130

FaroArm

Manual

January 2009

Chapter 2: CAM2® Measure Devices Menu

Hardware Configuration

Select DEVICES < HARDWARE
CONFIG from the DEVICES menu. In
the H

ARDWARE

ONFIGURATION

dialog

box you can:

• View the current information about

the FaroArm.

• Set the Arm Trigger mode.

• Enable/disable Stress Stops and

adjust the sensitivity.

See “Error and

Status Indicators” on page 14.

• Set the arm controlled mouse settings.

• Enable/disable Sleep Mode.

Click OK to accept the changes. Click
the CANCEL button to discard any changes and exit the command.

Stress Stops:

The default value is 0.182 and should rarely be set any

lower.

OTE

: For Advantage series FaroArms and Digital Template Arms

set the stress stop sensitivity at a maximum of 0.364.

FaroArm Controlled Mouse:

The movement of the mouse cursor can

be switched as it relates to the movement of the probe.

Set an option for the device’s BACK button. These options are ignored
during any measurement command.

• Application Specific - sends a special signal to the application

software. The software can use this special signal to launch any
command. For example, this repeats the last command in FARO’s
CAM2 Measure X.

Tracking Speed:

Adjust the speed of the cursor is adjusted using the

Tracking Speed Slider.

Sleep Mode:

The FaroArm shuts down with no activity after two hours.

IME

EFT

is the remaining time before the FaroArm shuts down.

08M46E00_FaroArmUSB.book Page 76 Tuesday, February 17, 2009 1:42 PM

Summary of Contents for FaroArm Fusion



































































































































Search results

Summary of Contents for FaroArm Fusion

Reviews:

Faro FaroArm Fusion, Manual, Page: 84 / 130

Search results

Summary of Contents for FaroArm Fusion

Reviews: