Faro FaroArm Fusion Manual Download Page 71

Page: 71 / 130

FaroArm

Manual

January 2009

Chapter 1: Introduction to the FaroArm

FARO Wireless FAQ

• How fast is the connection?

1 Megabit/second.

• What is the range of the FARO Wireless connection?

Approximately 30 feet or 10 meters.

• How many simultaneous Bluetooth wireless connections can be

established with the FaroArm driver?

Two.

• Can both USB and Bluetooth wireless FaroArms be connected

simultaneously?

Yes.

• Can a single FaroArm connect using both Bluetooth wireless and a

USB cable at the same time?

No. If both are properly connected, the Bluetooth wireless will be
the only active connection for that FaroArm.

• Can I use a FARO Laser Line Probe with the FARO Wireless

connection?

Yes.

• Can I add a Bluetooth wireless connection while the FaroArm driver

is already running?

No, the FaroArm driver must be unloaded before changing any
FARO Wireless settings.

• Why does it take longer for my measuring software to open when I

use the FARO Wireless connection?

The FaroArm driver requires more time to initialize when using a
FARO Wireless connection and this translates into slightly
increased load times for the measuring software.

• Why does it take longer for the P

ROBES

dialog box to go away when I

am using a FARO Wireless connection.

Probe data saves in the FaroArm and requires more time for this
information to transfer when using the FARO Wireless
connection.

08M46E00_FaroArmUSB.book Page 63 Tuesday, February 17, 2009 1:42 PM

Summary of Contents for FaroArm Fusion



































































































































Search results

Summary of Contents for FaroArm Fusion

Reviews:

Faro FaroArm Fusion, Manual, Page: 71 / 130

Search results

Summary of Contents for FaroArm Fusion

Reviews: