manualshive.com logo in svg

Farnell TRC-8543, Manual

Share
Download
Farnell TRC-8543 Manual Download Page 13

lengths may be allowed at lower bit rates, but you should analyze each node for

signal integrity problems.

High-Speed/Flexible Data-Rate CAN

The maximum number of nodes depends on the electrical characteristics of the

nodes on the network. If all nodes meet the ISO 11898 requirements, you can

connect at least 30 nodes to the bus. You can connect higher numbers of nodes if

the nodes’ electrical characteristics do not degrade signal quality below ISO 11898

signal level specifications.
The TRC-8543 electrical characteristics allow at least 110 CAN ports on a network.

Low-Speed/Fault-Tolerant CAN

The maximum number of nodes depends on the electrical characteristics of the

nodes on the network. If all of the nodes meet the requirements of Low-Speed/

Fault-Tolerant CAN, up to 32 nodes may be connected to the bus.

TRC-8543 Hardware Overview

The TRC-8543 has one full-featured CAN port that is isolated from the host it is

plugged into. Software can select between either an NXP TJA1043T High-Speed CAN

transceiver or NXP TJA1055T Low-Speed/Fault-Tolerant CAN transceiver by

controlling on-board relays. The TJA1043T is fully compatible with the ISO 11898

standard and supports baud rates up to 2 Mbps. The NI-XNET driver enables baud

rates up to 8 Mbps. The TJA1055T is fully compatible with the ISO 11898 standard

and supports baud rates up to 125 Kbps.

Figure 9. 

TRC-8543 Hardware Overview

© National Instruments

13

TRC-8543

Summary of Contents for TRC-8543























Reviews:

No comments

Brands by name

Popular brands

Load more brands