FarmTek 113539 Page 3 Manual Download

Page: 3 / 31

Revision date: 01.13.21

113539

110725

Air Pump

109260 Air Stone

110722

Utility Pump

110408

1/8" White Polyethylene Tubing

111698 Ratchet Clamp

WR1095

Tape

Plastic Pipe & Tube Cutter

111128 (4)

End Cap w/ Outlet

111127 (4)

End Cap No Outlet

Important Information

PICTORIAL GUIDE

The following graphics and photos will help identify the different parts of the hydroponic system. (Some

parts may not be shown.) To prevent mixing of fittings, select only those that are needed for each procedure.

Keep all fittings in the shipping bags until they are needed.

10015106

Short Tee Fitting (12)

100442 (1)

Nut Setter

FA4470B (10)

Tek Screw

WF6990

PVC Cement

and

113372 Purple

Primer

PVC PRIMER & PVC CEMENT

Follow all directions printed

on pvc primer and cement

containers.

Purple color of

primer does not fade

! Use

caution during application

to reduce spills and over

application at joints.

Prime all joints before

assembly.

WF6504A

3/4" Black Hose

110091 Clear Vinyl Tubing

Summary of Contents for 113539
































Search results

Summary of Contents for 113539

Reviews:

Related manuals for 113539

Brands by name

Popular brands

FarmTek 113539, Manual

Search results

Summary of Contents for 113539

Reviews:

Related manuals for 113539

Brands by name

Popular brands