FarmTek 113539 Page 19 Manual Download | Manualshive

Page: 19 / 31

background image

19

Revision date: 01.13.21

113539

12

ASSEMBLE FILTER/VALVE, PUMP AND MAIN SUPPLY LINE

Assembly Instructions

1. Take the 106808 hangers and attach two to the inside of the

crossbar at the drain end of the frame using the FA4470B Tek

screws. Consult the photo at the right for dimensions.

2. Move to the middle crossbar and attach the last 106808

hanger to the underside of that crossbar.

3. Using the photo below, assemble the filter/valve and related

fittings. Wrap all threads with thread tape before assembly.

3"

8"

106808 Hanger

WF3310

FA4470B (10)

Tek Screw

WF3411

112066 (1) Shut-

off to attach to

WF1023 filter.

WF2153

WF3411

WF3310

WF1023

112066

WF2153

Install hanger tight to

tee fitting of the frame.

4. Continue with the next procedure.

WF1023 Filter (1)

Cap

Remove cap

to install the

112066 shutoff

valve.

WR1095

Tape

«
...
17
18
19
20
21
...
»

Summary of Contents for 113539
































Reviews:

No comments

Related manuals for 113539

Brand: Rangevision Pages: 31

Brand: Makita Pages: 8

Brand: VECTECH Pages: 5

Brand: Fisher Scientific Pages: 42

Brand: Raven Pages: 17

Brand: Raymarine Pages: 124

Brand: Raymarine Pages: 192

Brand: Laserworld Pages: 8

Brand: Laserworld Pages: 6

Brand: LaserLiner Pages: 56

Brand: LaserLiner Pages: 54

Brand: Quark-Elec Pages: 2

Brand: Lafayette Pages: 10

Brand: Safco Pages: 2

Vetter QuickStrut

Brand: Idex Pages: 14

Brand: American DJ Pages: 12

Brand: aion Pages: 10

Brand: COOPS & FEATHERS Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands