Farmet VIDIUM P 350 Operating Manual Download | Manualshive

Page: 18 / 24

background image

Manual

VIDIUM P 350 | P 450

18

│

24

5.3.4

Setting the Depth of the Double Supporting Wheel

Pull out the ball K of the corresponding lever of the supporting wheel St and turn it by 90°. Move the
supporting wheel R into the required depth and snap the ball back in.

5.3.5

Setting the Depth of the Swivelling Supporting Wheel

The depth is set using the setting bolt E separately for both sides.

Greater working depth: Screw the setting bolt E in
Lower working depth: Screw the setting bolt E out

!

Put the setting screw E into the horizontal position and secure it with safety nut K!

«
...
16
17
18
19
20
...
»

Summary of Contents for VIDIUM P 350

























Reviews:

No comments

Related manuals for VIDIUM P 350

Brand: Daavlin Pages: 13

Brand: Daavlin Pages: 27

Brand: Fender Pages: 15

Brand: J D Squared Pages: 18

Brand: Eagle Pages: 3

Brand: K&K Pages: 8

Brand: Datavideo Pages: 28

Brand: Gamry Instruments Pages: 69

Brand: Gamry Instruments Pages: 30

Brand: Gamry Instruments Pages: 88

Brand: Rayger Pages: 2

Brand: Omlet Pages: 2

Brand: Omicron Pages: 382

Brand: Omicron Pages: 188

Brand: quadient Pages: 188

Brand: Radarsign Pages: 16

MOSQUITOTRAP MIE5

Brand: Jata hogar Pages: 20

Brand: Stiga Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands