Farmet KOMPAKTOMAT K1000PS Operating Manual Download | Manualshive

Page: 48 / 56

background image

Manual

KOMPAKTOMAT K500PS | K600PS | K700PS | K800PS | K1000PS

48

│

56

10.1

LUBRICATION PLAN FOR THE MACHINE

Regular  lubrication  of  lubricating  places  increases  the  usable  life  of  the  nodes  and  the  machine.  Perform
lubrication according to the “Lubrication Plan".
When lubricating the bearings of the rollers, observe caution so that you do not damage the bearings. When
lubricating the bearings of the rollers, turn the roller around so that the lubricant spreads evenly.
Lubricate the nodes until clean lubricant is coming out of them. Then wipe the lubricant off.

Places and intervals of lubrication

PLACE FOR LUBRICATION

INTERVAL

LUBRICANT

Controlling handle

-Always  before  work  with  the
machine.
Always  after  the  work  and  before
putting the machine out of operation.

-Plastic lubricant according to

DIN 51 502

1) K EP2 - 30

2) KP2P-20 Likx

Pole joint

Lubricating the controlling handle

Lubricating the pole joint

MANIPULATION WITH LUBRICANTS:



Treat oils and lubricants as hazardous waste according to valid regulations and acts.



Protect yourself from direct contact with oils by using gloves or protective lotion.



Wash oil stains on skin thoroughly with warm water and soap. Do not clean the skin with petrol, diesel oil
or other dissolving agents.



Oil or lubricant is poisonous. If you swallow any, immediately seek a doctor.



Keep oil and lubricants out of reach of children.

«
...
46
47
48
49
50
...
»

Summary of Contents for KOMPAKTOMAT K1000PS

























































Reviews:

No comments

Related manuals for KOMPAKTOMAT K1000PS

WJHD309A - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 79

Brand: ZIGBEE Pages: 4

Brand: CAIRE Pages: 38

Brand: Caframo Pages: 72

Brand: Eaton Pages: 16

Brand: Eaton Pages: 6

Brand: Ecco Pages: 17

Brand: Rane Pages: 6

Brand: Rane Pages: 27

Brand: Ranger Products Pages: 6

Brand: Rane Pages: 88

Brand: Haag-Streit Pages: 21

Brand: Yamaha Pages: 31

Brand: XFit Pages: 16

BlackBox Series

Brand: Nakamichi Pages: 23

Brand: Harken Pages: 4

Brand: Abbriata Pages: 27

Brand: A&D Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands