Farmet 2021/0625 Operating Instruction Download | Manualshive

Page: 25 / 102

background image

24

11

Machine fan

- The hydraulic drive of the fan is driven directly from the tractor switchboard.

- It is necessary that

the fan drive is connected to the tractor’s priority circuit to ensure that the fan speed

does not drop in any sense.

- The fan speed is set directly in the tractor by regulating the oil flow of the circuit.

- Replacing of the quick coupling for the waste branch with less than ISO 20 is unacceptable.

Hydraulic fan motor

Hydraulic engine capacity per revolution

8 cm

3

/rev.

Small fan

Maximum speed

5500 (rev. /min.)

Minimum speed

1000 (rev. /min.)

Pressure branch (P)

Minimum pressure in the pressure hose

130 (bar)

Maximum pressure flow in the pressure hose

50 (l/min.)

Return waste branch (T)

Maximum pressure in the return waste branch

5 (bar)

In case, if free waste is not fitted to the tank as standard on the tractor, contact the tractor manufacturer
(dealer), who will provide you with information on the options for the free waste terminal.

1

Small fan

V1

4

Pressure hose ISO 12.5 (P)

2

Reverse throttle valve

5

Return waste branch ISO 20 (T)

3

Hydraulic engine

*See

page 3

for your machine configuration.

1

3

4

5
c

2

«
...
23
24
25
26
27
...
»

Summary of Contents for 2021/0625







































































































Reviews:

No comments

Related manuals for 2021/0625

Brand: B&K Pages: 5

Brand: B&K Pages: 28

Brand: Hanil Pages: 60

WJHD309A - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 79

Brand: Panasonic Pages: 30

Brand: Raytech Pages: 21

Brand: Teac Pages: 2

Brand: laerdal Pages: 2

Brand: Tascam Pages: 27

Brand: Jay-Lor Pages: 72

Brand: MacDon Pages: 198

Brand: M-Triangel Pages: 6

Brand: Backyard Discovery Pages: 51

Brand: Nautilus Pages: 12

Brand: CAIRE Pages: 16

PORTABLE ICE FISHING KIT

Brand: Garmin Pages: 5

Brand: Omlet Pages: 60

VIMCO Sivoia SV-CCI-GRP

Brand: Lutron Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands