Farm King Model 1050 Operator And Parts Manual Download Page 18

Page: 18 / 174

Safety - 10" Backsaver Auger

OPERATING SAFETY ZONE

Safety Zone Identification

AVOID INJURY OR DEATH

•

Do not allow small
children, bystanders or
unauthorized persons in
the work area during
operation.

•

Never stand or work under
the auger and
undercarriage when in the
raised position or during
operation.

•

Always keep PTO shields
and all guards in place
during operation.

•

Keep away from moving
parts.

•

Keep everyone clear when
operating the hopper
mover.

•

Owners and operators
should allow only
authorized personnel and
grain transport vehicles
near the auger or inside
the work area.

•

Allow adequate space for
grain transport vehicles to
operate safely.

•

Make certain everyone is
clear of the equipment
before applying power or
moving the machine.

•

While in operation, always
support the discharge end
or provide adequate
anchorage of the intake
end to prevent sudden
tipping.

ELECTROCUTION HAZARD

Keep away from power lines

electrocution can occur

without direct contact.

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands