Farm King Model 1050 Operator And Parts Manual Download Page 165

Page: 165 / 174

163

Specifications - 10" Backsaver Auger

HARDWARE TORQUE VALUES (CONT’D)

Imperial Chart

NOTE: Do not use the values listed in the charts if a different torque value or tightening procedure is specified in

this manual for a specific application. Torque values listed are for general use only.

Use the following charts to determine the correct torque when checking, adjusting or replacing hardware.

Torque values are listed in newton-meters (inch* or foot pounds) for normal assembly applications.

Nominal

Size

SAE Grade 5

SAE Grade 8

LOCK NUTS

Unplated

Plated

Silver

Plated

W / ZnCr

Gold

Unplated

Plated

Silver

Plated

W / ZnCr

Gold

Unplated

Plated

Silver

Plated

W / ZnCr

Gold

Grade

W / Gr. 5

Bolt

Grade

W / Gr. 8

Bolt

1/4

6.2 (55*)

8.1 (72*)

9.7 (86*)

12.6

(112*)

13.6

(121*)

17.7

(157*)

6.9 (61*)

9.8 (86*)

5/16

13 (115*) 17 (149*) 20 (178*) 26 (229*) 28 (250*) 37 (324*) 14 (125*) 20 (176*)

3/8

23 (17)

30 (22)

35 (26)

46 (34)

50 (37)

65 (48)

26 (19)

35 (26)

7/16

37 (27)

47 (35)

57 (42)

73 (54)

80 (59)

104 (77)

41 (30)

57 (42)

1/2

57 (42)

73 (54)

87 (64)

113 (83)

123 (91)

159 (117)

61 (45)

88 (64)

9/16

81 (60)

104 (77)

125 (92)

163 (120) 176 (130) 229 (169)

88 (65)

125 (92)

5/8

112 (83)

145 (107) 174 (128) 224 (165) 244 (180) 316 (233)

122 (90)

172 (127)

3/4

198 (146) 256 (189) 306 (226) 397 (293) 432 (319) 560 (413) 217 (160) 306 (226)

7/8

193 (142) 248 (183) 495 (365) 641 (473) 698 (515) 904 (667) 350 (258) 494 (364)

289 (213) 373 (275) 742 (547) 960 (708) 1048 (773)

1356

(1000)

523 (386) 739 (545)

NOTE: Torque values shown with * are inch pounds.

Identification of Hex Cap Screws and Carriage Bolts

Identification of Hex Nuts and Lock Nuts

SAE GRADE

2 BOLTS

SAE GRADE

5 BOLTS

SAE GRADE

8 BOLTS

SAE GRADE

2 NUTS

SAE GRADE

2 NUTS

SAE GRADE

2 NUTS

Grade A - No Notches

Grade B - One Circumferential Notch

Grade C - One Circumferential Notches

Grade A - No Mark

Grade B - Letter B

Grade C - Letter C

Grade A - No Marks

Grade B - Three Marks

Grade C - Six Marks

(Marks not always located at corners)

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Brands by name

Popular brands