Farm King BW200 Operator And Parts Manual Download Page 75

Page: 75 / 82

Specifications And Shipping Kit Numbers - 200 Bale Wrapper

HARDWARE TORQUE VALUES

Metric Chart

NOTE

Do not use the values listed in the charts if a different torque value or tightening procedure is

specified in this manual for a specific application. Torque values listed are for general use only.

Use the following charts to determine the correct torque when checking, adjusting or replacing hardware.

Torque values are listed in newton-meters (inch* or foot pounds) for normal assembly applications.

Nominal

Size

Class 5.8

Class 8.8

Class 10.9

Lock nuts

Unplated

Plated

W / ZnCr

Unplated

Plated

W / ZnCr

Unplated

Plated W /

ZnCr

CL.8 W/ CL.

8.8 Bolt

1.7 (15*)

2.2 (19*)

2.6 (23*)

3.4 (30*)

3.7 (33*)

4.8 (42*)

1.8 (16*)

5.8 (51*)

7.6 (67*)

8.9 (79*)

12 (102*)

13 (115*)

17 (150*)

6.3 (56*)

14 (124*)

18 (159*)

22 (195*)

28 (248*)

31 (274*)

40 (354*)

15 (133*)

M10

28 (21)

36 (27)

43 (32)

56 (41)

61 (45)

79 (58)

30 (22)

M12

49 (36)

63 (46)

75 (55)

97 (72)

107 (79)

138 (102)

53 (39)

M16

121 (89)

158 (117)

186 (137)

240 (177)

266 (196)

344 (254)

131 (97)

M20

237 (175)

307 (226)

375 (277)

485 (358)

519 (383)

671 (495)

265 (195)

M24

411 (303)

531 (392)

648 (478)

839 (619)

897 (662)

1160 (855)

458 (338)

NOTE: Torque values shown with * are inch pounds.

Identification of Hex Cap Screws and Carriage Bolts - Classes 5 and up

Identification of Hex Nuts and Lock Nuts - Classes 5 and up

XYZ

8.8

AB
CD

MANUFACTURER’S IDENTIFICATION

PROPERTY CLASS

CLOCK MARKED

Summary of Contents for BW200



















































































Search results

Summary of Contents for BW200

Reviews:

Brands by name

Popular brands

Farm King BW200, Operator And Parts Manual

Search results

Summary of Contents for BW200

Reviews:

Brands by name

Popular brands