manualshive.com logo in svg

Fanvil PA2, User Manual, Page: 10 / 57

Share
Download
Fanvil PA2 User Manual Download Page 10

 

 

    4 

5.2   Install 

Before you start using the device, please install the following: 

5.2.1 

button instruction 

 

   

Picture 1 - button instruction

 

The image above shows the key layout of the device. Each button provides its own specific function. 

The user can refer to the instructions for the keys in the illustration in this section to operate the device. 

Table 1 - button instruction

 

Label 

Explanation 

①

 

Speaker interface 

according to the device input voltage adaptive output maximum power; 4Ω         

speaker, POE / 10W, 12V / 10W, 18V / 20W, 24V / 30W. The greater the horn 

impedance, the smaller the output power. Suggested wire diameter: 18AWG or larger 

diameter.

 

②

 

Headset interface 

Speaker audio line signal output impedance 32 Ohm, single ended output voltage 1.2V, 

used for external headphones or active speakers

 

③

 

LED interface 

Output 5V voltage 5 mA current, can be an external LED, indicating the network status, 

call status, registration status.

 

④

 

Function key interface 

connection switch, you can log on page set the call number or IP address.

 

⑤

 

Microphone interface 

Recommend the use of 2.2K Ohm impedance electret condenser microphone, 

sensitivity: -38dB, bias voltage 2.2V. Microphone signal cable it is recommended to use 

a shielded cable and do not connect the shield cable to the grounding screw, improve 

Summary of Contents for PA2


























































Reviews:

No comments